Double layer PCB, on FR4 support, with over 95% ground plane on each side.
The best layer synchronizing (over 99,5%) could be done it from Eagle files.
Below is the BOTTOM layer of above double layer pcb.
The best layer synchronizing (over 99,5%) could be done it from Eagle files.
Below is the BOTTOM layer of above double layer pcb.
An externally hosted image should be here but it was not working when we last tested it.
Last edited:
Below 4 pcb's done it on tinned CEM3 suport , have been manufactured for our forum friend RCruz (Ricardo).
I hope that he will enjoy my releases, as soon he will receive them.
I hope that he will enjoy my releases, as soon he will receive them.
An externally hosted image should be here but it was not working when we last tested it.
Thank you so much for your help Mihai. The boards look very good. Will now start populating and after I will leave a subjective comment here 🙂
Hi Ricardo,
Thanks a lot for your appreciation.
Please feel free to post here your "populated boards". (solder sides + components sides).
Because our communication was perfect one, I'll try to help you with next PCB projects, if my available time allow this.
All the best,
Mihai
Thanks a lot for your appreciation.
Please feel free to post here your "populated boards". (solder sides + components sides).
Because our communication was perfect one, I'll try to help you with next PCB projects, if my available time allow this.
All the best,
Mihai
Last edited:
Cheapest_PCB on CEM3 professional support.
Cutting of boards are FREE for any cutting type (linear or curved)
I offer you for free:
-TINNING (only for CEM3 support)
-DRILLING
CEM3 has min. 22 um ( max.25 um)
Cutting of boards are FREE for any cutting type (linear or curved)
I offer you for free:
-TINNING (only for CEM3 support)
-DRILLING
CEM3 has min. 22 um ( max.25 um)
An externally hosted image should be here but it was not working when we last tested it.
Below can be found the SILKSCREEN (components mask) of above round pcb's.
An externally hosted image should be here but it was not working when we last tested it.
Last edited:
Cheapest double layer PCB boards on FR4 support.
The pcb's are TINNED on both sides.
Below can be seen the BOTTOM layer.
The pcb's are TINNED on both sides.
Below can be seen the BOTTOM layer.
An externally hosted image should be here but it was not working when we last tested it.
Last edited:
Hi Mayank,
I already answered you, and I look for answers according my questions directly to my private e-mail address. Will talk there about the way to help you.
Regards,
Mihai
I already answered you, and I look for answers according my questions directly to my private e-mail address. Will talk there about the way to help you.
Regards,
Mihai
Cheapest double layer PCB boards on FR4 support.
The pcb's are TINNED on both sides.
Below can be seen the TOP layer of above shown boards.
The pcb's are TINNED on both sides.
Below can be seen the TOP layer of above shown boards.
An externally hosted image should be here but it was not working when we last tested it.
Hi Ricardo,
First of all, I thank you, for posted pictures in my thread.
You did a great job.
I hope that the "sound" is near hi-end, and you'll enjoy for your realised amp.
We'll be in touch for next pcb projects.
All the best from Romania,
Mihai
🙂
First of all, I thank you, for posted pictures in my thread.
You did a great job.
I hope that the "sound" is near hi-end, and you'll enjoy for your realised amp.
We'll be in touch for next pcb projects.
All the best from Romania,
Mihai
🙂
Last edited:
80 pins adapter - FR4 - tinned
An externally hosted image should be here but it was not working when we last tested it.
Dear Namcir,
I have not available time to design the pcb's.
Always I manufacture the pcb's ( as presented boards in this thread) , from different ready designed boards.
Files accepted: Eagle, ExpressPCB, DipTrace or pdf , jpeg ( at least 600 dpi)
Thanks for your understanding,
Mihai
I have not available time to design the pcb's.
Always I manufacture the pcb's ( as presented boards in this thread) , from different ready designed boards.
Files accepted: Eagle, ExpressPCB, DipTrace or pdf , jpeg ( at least 600 dpi)
Thanks for your understanding,
Mihai
Cheapest PCB's on CEM3 with FREE TINNING.
DRILLING is FREE for CEM3 and FR4
DRILLING is FREE for CEM3 and FR4
An externally hosted image should be here but it was not working when we last tested it.
Cheapest PCB's on FR4 support
The TINNING is also FREE for FR4 with 1 mm thickness ( NOT for 1,5 mm FR4 support)
The FR4 support with 1 mm thickness has at least 80% transparency.
The TINNING is also FREE for FR4 with 1 mm thickness ( NOT for 1,5 mm FR4 support)
The FR4 support with 1 mm thickness has at least 80% transparency.
An externally hosted image should be here but it was not working when we last tested it.
FREE SHIPPING cost for any pcb's delivered in Europe.
That is valid for period: 15 Dec 2014 - 30 March 2015 , and weight packages less than 250 grames.
That is valid for period: 15 Dec 2014 - 30 March 2015 , and weight packages less than 250 grames.
Last edited: