thanks
i dont have more pin in my micro to creat thermal with micro
if i want use micro for that i must change my micro ic with Atmega 1280 or some thing like that to have enoufe pin to do that and even i need to use interupt for sensor
it make my micro PCB messy
thanks for your helping
i dont have more pin in my micro to creat thermal with micro
if i want use micro for that i must change my micro ic with Atmega 1280 or some thing like that to have enoufe pin to do that and even i need to use interupt for sensor
it make my micro PCB messy
thanks for your helping
[special=]%[/special]
this nucleus has to calculate the primary
Nano
Did you use the core I recommended?load testing on 400 Watts
this nucleus has to calculate the primary
Nano
manojtm ,what chip do you use for dts/ac3 digital input?To my knowledge there is none available for public due to copyright law.
Hi CPX,
good day man we need your valuable comments i am very happy you are again join here
not one single IC complete circuit with SPDIF input
Regards
MANOJ
thanks for your reaply but i dont know hove can i use that
i mean hove can control amp with this thermal switch
were i must conect it?
Hi Hadi,
connect across 100n capacitor in power AUD600 board.near by 12V bias connection(center pin and -ve pin)
Regards
MANOJ
Hi friends
sir manoj
i am wating for your reaply and for converter
thanks very much
Hi Hadi,
You can use this. this is not my circuit
Regards
MANOJ
Attachments
thanks to manoj
i creat this befor with IRFZ44N mosfet
it wath work good
this is kenwood KAV-716 smps
this smps can handel 300 watt if drive mosfets good
we need more power
how can i drive more mosfet with this?
how can i increse this smps ferecuence?
thanks FriendHi Hadi,
You can use this. this is not my circuit
Regards
MANOJ
i creat this befor with IRFZ44N mosfet
it wath work good
this is kenwood KAV-716 smps
this smps can handel 300 watt if drive mosfets good
we need more power
how can i drive more mosfet with this?
how can i increse this smps ferecuence?
Hi
i need mosfet driver for drive 5 + 5 IRFZ44N for this smps
any sugetion?
Hi Hadi,
Use IRF3205 x 2 with 47 Ohm gate resistor freq=80KHz or 100KHz. Primary turns 3+3
Regards
MANOJ
thanks to manoj
it is not posible to handel 110A in TO220 case.
you mean i must use 4 IRF3205 ?
can this handel + - 30VDC 20A ?
thanks for your reply
Hi my dear friendHi Hadi,
Use IRF3205 x 2 with 47 Ohm gate resistor freq=80KHz or 100KHz. Primary turns 3+3
Regards
MANOJ
it is not posible to handel 110A in TO220 case.
you mean i must use 4 IRF3205 ?
can this handel + - 30VDC 20A ?
thanks for your reply
hi fra, what type of toroidal core can i used on this design? it may handle a large amount of current is it a low or high permeability type?any idea and how about the outside & internal diameter, thickness of this core that your going to used?is it available in the market?thank's
hi fra, what type of toroidal core can i used on this design? it may handle a large amount of current is it a low or high permeability type?any idea and how about the outside & internal diameter, thickness of this core that your going to used?is it available in the market?thank's
I use a t106-2 core.
You might need a slightly bigger core for your current needs.
the t106 is 1.06 inches diameter and the -2 is the core type.
- Home
- Amplifiers
- Class D
- UCD 25 watts to 1200 watts using 2 mosfets