Go Back   Home > Forums > >

Solid State Talk all about solid state amplification.

Stability of an amplifier under capacitive loading
Stability of an amplifier under capacitive loading
Please consider donating to help us continue to serve you.

Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving
Reply
 
Thread Tools
Old 4th September 2020, 05:08 PM   #1
profdc9 is offline profdc9
diyAudio Member
 
Join Date: Aug 2020
Default Stability of an amplifier under capacitive loading

When driving a speaker on a long cable, what is a safe capacitance to design an amplifier to be stable driving? Would 10 nF be a sufficient maximum capacitance or 100 nF? I measured some audio cable at about 400 pF/m, but I would guess that the variations in setups might produce higher capacitance loads. Are audio amps ever designed to be unconditionally stable with respect to capacitive loading, and if so, how? Given that oscillation of an amplifier could produce a catastrophic effect on a speaker if the amplitude was high enough, I would think this might be a consideration to maintain SOA.
  Reply With Quote
Old 4th September 2020, 06:44 PM   #2
duncan2 is offline duncan2  United Kingdom
diyAudio Member
 
Join Date: Mar 2013
Location: Scotland.
VERY touchy subject !

This has split audio designers right down the middle just ask D.Self (or read his article in EW ) where in reply to several articles by another engineer cut him to ribbons by presenting an article "proving " that ring mains electric cable was just as good .


It didn't end there verbal fisticuffs ensued and the Editor had to calm things down .
Naim audio specified that their amps required special cables and that other types of cables could cause "problems ".


Those were the days of low capacitance cable/low inductive cable /low resistivity cable etc , from what I remember during the 80,s/90,s in EW .


I hope calmer minds are at work here as I was engrossed by each monthly episode of EW in the Letters & articles printed , things are a lot more duller now there.


Loudspeakers: Effects of amplifiers and cables – Part 4 | EE Times

Last edited by duncan2; 4th September 2020 at 06:49 PM. Reason: additional info
  Reply With Quote
Old 4th September 2020, 06:52 PM   #3
Mark Johnson is offline Mark Johnson  United States
diyAudio Donor
diyAudio Member
 
Mark Johnson's Avatar
 
Join Date: May 2011
Location: Silicon Valley
Stability of an amplifier under capacitive loading
Some people also say that some types of loudspeakers are themselves capacitive. So even if the cable length is 10 centimeters, the capacitance load driven by the amplifier is high.

One reason why some amplifier designers install an inductor in series between the amplifier output and the loudspeakers, is to improve stability when the load is capacitive. Other amplifier designers brag that they have no / need no series inductor.
  Reply With Quote
Old 4th September 2020, 07:24 PM   #4
cbdb is offline cbdb  Canada
diyAudio Member
 
Join Date: Oct 2008
Location: Vancouver
With all the wacky (audiophool) speaker cable out there why would any amp maker exclude the zobel? I guess to market the thing too the fools that buy that sort of cable? So marketing.
  Reply With Quote
Old 4th September 2020, 07:35 PM   #5
rayma is offline rayma  United States
diyAudio Member
 
Join Date: Apr 2011
Depending on the output network, many amplifiers will be stable for very large and for very small capacitances,
but not for a certain range of intermediate values. This is typical for many types of feedback amplifiers in general.

Last edited by rayma; 4th September 2020 at 08:04 PM.
  Reply With Quote
Old 4th September 2020, 08:23 PM   #6
duncan2 is offline duncan2  United Kingdom
diyAudio Member
 
Join Date: Mar 2013
Location: Scotland.
What helped get all this going see -WW+EW -December 1996.


Even earlier---February 1995 relating to Mark,s post.

Last edited by duncan2; 4th September 2020 at 08:31 PM. Reason: additional info
  Reply With Quote
Old 4th September 2020, 08:55 PM   #7
rayma is offline rayma  United States
diyAudio Member
 
Join Date: Apr 2011
Very nice notes:
Practical Techniques to Avoid Instability Due to Capacitive Loading | Analog Devices
Op Amps Driving Capacitive Loads | Analog Devices
https://www.ti.com/lit/an/sloa020a/s...oogle.com%252F

Last edited by rayma; 4th September 2020 at 08:57 PM.
  Reply With Quote
Old 4th September 2020, 10:03 PM   #8
profdc9 is offline profdc9
diyAudio Member
 
Join Date: Aug 2020
Default simulation of C300 amplifier

I am working on building up Michael Chua's C300 amplifier which does include a Zobel load on it. I have a SPICE simulation of it going. I am trying to figure out what could go wrong with it through simulation. I have been able to put 10 to 20 nF on it without problems, but once 100 nF is directly loaded on it, oscillations start. I can increase the Miller compensation capacitor to bring the pole down to be stable, but if the loop bandwidth is reduced too much, THD increases. It seems to be in the neighborhood of 0.05% to 0.1% for 20 kHz @ 200 W output to an 8 ohm load (at least in simulation).



The attached SPICE file is used with Qucs-S/ngspice and uses combinations of faster transistors to try to increase the loop bandwidth so that the dominant pole is the Miller capacitance. If anyone uses Qucs-S you can load this model up and try it for yourself.


This is why I need to have some idea of what a reasonable capacitance to design for is. 100 nF seems like a lot of capacitance for a cable, but perhaps someone has some ribbon-like audio cable that works that way.
Attached Images
File Type: png C300_simulation_circuit.png (72.8 KB, 478 views)
File Type: png C300_simulation_circuit_results.png (26.3 KB, 484 views)
Attached Files
File Type: zip C300_Qucs_S_Spice_Simulation.zip (104.2 KB, 11 views)
  Reply With Quote
Old 4th September 2020, 11:30 PM   #9
steveu is offline steveu  United States
diyAudio Member
 
Join Date: May 2005
Location: Colorado Springs
Default optimizing feedback

Unfortunately, there will always be a feedback arrangement that provides a bit less distortion at the price of stability. You have to do everything you can to stabilize your feedback and then look to other means to reduce distortion. For example, replacing R31+R32 with a single resistor and perhaps a capacitor (no connection to the final output) in order to cross-couple the drivers will improve the cross-over and high frequency performance.
C6 should be limited with a series resistor, 100 to 1k depending on R14. C6 causes RF rectification problems because it is a direct path from the speaker cable antenna to the LTP. C6 also exaggerates unpredictable problems that result from stray capacitance and inductance.
There are many complicated compensation methods but complicated compensation is vulnerable to unexpected variations that cause instability. My favorite plan is KISS, a single dominant pole. So I would not use R5+C3, and simply adjust C9 and/or R6...R10 until the circuit is stable.
Not using a series inductor +resistor in the output is leaving the feedback wide open vulnerable to all kinds of stability issues. I would only omit the inductor if the amp is integral to the speaker, ie no speaker cables to speak of, and the speaker impedances well defined.
  Reply With Quote
Old 4th September 2020, 11:33 PM   #10
rayma is offline rayma  United States
diyAudio Member
 
Join Date: Apr 2011
"Not using a series inductor +resistor in the output is leaving the feedback wide open vulnerable to all kinds of stability issues. I would only omit the inductor if the amp is integral to the speaker, ie no speaker cables to speak of, and the speaker impedances well defined."

Definitely, who wants full power oscillation at 200kHz?
That lower distortion is illusory if it is only available along with conditional stability.

Last edited by rayma; 4th September 2020 at 11:41 PM.
  Reply With Quote

Reply


Stability of an amplifier under capacitive loadingHide this!Advertise here!
Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
New Amplifier Build Stability H713 Solid State 37 15th May 2020 09:20 AM
SMPS - Capacitive loading knutn Power Supplies 19 27th August 2019 10:40 PM
Stability into capacitive loads aros71 Tubes / Valves 8 23rd July 2017 06:34 AM
"Tuning phonograph reproduction...capacitive loading & channel balancing" RCAguy Analogue Source 0 3rd March 2015 04:57 PM
good ESL amplifier that works with extreme capacitive loads thadman Solid State 2 1st February 2007 12:20 AM


New To Site? Need Help?

All times are GMT. The time now is 09:00 AM.


Search Engine Optimisation provided by DragonByte SEO (Pro) - vBulletin Mods & Addons Copyright © 2020 DragonByte Technologies Ltd.
Resources saved on this page: MySQL 14.29%
vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2020 DragonByte Technologies Ltd.
Copyright ©1999-2020 diyAudio
Wiki