Group buy for Augerpro Scan-Speak waveguide (circular version) - Page 4

pfarrell · 1st August 2020, 09:00 PM

Aluminum yes. Finish seems applied vs. anodized. Weighty. Quality is beyond cost IMO.

Brett · 26th December 2020, 05:13 AM

Are there still some WGs available?

mbrennwa · 26th December 2020, 12:31 PM

Yes, they are available.

MICHARGE · 19th January 2021, 10:40 PM

Hello! Kinda late for the group buy, wish I knew about this thread when I was building my own speakers with an R3004/662000 late 2020... May I ask: do you have some waveguides in stock from group buys? Circular would be best but I could perhaps settle for the elliptical one. I might consider rebuilding my speakers with it in the future...
Kind Regards

mbrennwa · 20th January 2021, 06:51 AM

I am not sure why this question comes up again and and again every few weeks. The answer has always been the same...

Y E S T H E Y A R E I N S T O C K ! ! !

( And if they run out, a new batch can be done -- it's all in the first post )

Is there anything I could do to make this clear(er)?

MICHARGE · 20th January 2021, 12:44 PM

Oops my apologies I thought I did my homework right but reading through all threads of yours would it be the Monkey coffin or the other group buy thread I must have overlooked the very last bullet point in the first post stating they are in stock...Please understand me usually the group buys I took part in once they're gone: they're gone, it's unusual that a group buy organiser takes on the burden to keep extra in stock with the possibility to never sell them, I commend you for that.

As soon as my exams are over you will receive a PM with all the relevant info as stated in post n°1.

Since you asked; to make it clearer I would emphasize the (*)Notes: section in your first post, perhaps having those at the top? Again apologies for that mbrennwa!

Best Regards

mbrennwa · 20th January 2021, 03:31 PM

Ok, I see. I added a note on top of the first post

26th December 2020, 12:31 PM	#33
mbrennwa diyAudio Member Join Date: Mar 2005 Location: Zurich, Switzerland	Yes, they are available. __________________ ------ Waveguides for Scan-Speak tweeters – MATAA audio analyser – Open Source Monkey Coffin

20th January 2021, 06:51 AM	#35
mbrennwa diyAudio Member Join Date: Mar 2005 Location: Zurich, Switzerland	I am not sure why this question comes up again and and again every few weeks. The answer has always been the same... Y E S T H E Y A R E I N S T O C K ! ! ! ( And if they run out, a new batch can be done -- it's all in the first post ) Is there anything I could do to make this clear(er)? __________________ ------ Waveguides for Scan-Speak tweeters – MATAA audio analyser – Open Source Monkey Coffin

20th January 2021, 03:31 PM	#37
mbrennwa diyAudio Member Join Date: Mar 2005 Location: Zurich, Switzerland	Ok, I see. I added a note on top of the first post __________________ ------ Waveguides for Scan-Speak tweeters – MATAA audio analyser – Open Source Monkey Coffin

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Waveguide to suit Peerless HDS/Scan-Speak D2608/91300	Joe Rasmussen	Group Buys	9	8th February 2020 05:28 AM
Group buy for Augerpro Scan-Speak waveguide (5" version A)	mbrennwa	Group Buys	32	29th July 2019 12:45 PM
Speak Waveguide Tutorial?	Tenson	Multi-Way	0	26th March 2013 09:27 PM
FS: Scan-Speak Illuminator d3004/60200 Tweeters, Scan-Speak Discovery 10f Midrange	bikinpunk	Swap Meet	1	27th September 2010 04:13 PM
Scan Speak 23W sub	Pan	Subwoofers	15	26th December 2007 07:13 PM

New To Site?	Need Help?
Register to Participate Privacy Statement Contact Us	Frequently Asked Questions Did you forget your password? Mark Forums Read


	Please consider donating to help us continue to serve you. Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving

1st August 2020, 09:00 PM	#31
pfarrell diyAudio Member Join Date: May 2019 Location: Upstate, NY	Aluminum yes. Finish seems applied vs. anodized. Weighty. Quality is beyond cost IMO.

26th December 2020, 05:13 AM	#32
Brett diyAudio Member Join Date: Jan 2002	Are there still some WGs available?

19th January 2021, 10:40 PM	#34
MICHARGE diyAudio Member Join Date: May 2020 Location: Wallonia	Hello! Kinda late for the group buy, wish I knew about this thread when I was building my own speakers with an R3004/662000 late 2020... May I ask: do you have some waveguides in stock from group buys? Circular would be best but I could perhaps settle for the elliptical one. I might consider rebuilding my speakers with it in the future... Kind Regards

20th January 2021, 12:44 PM	#36
MICHARGE diyAudio Member Join Date: May 2020 Location: Wallonia	Oops my apologies I thought I did my homework right but reading through all threads of yours would it be the Monkey coffin or the other group buy thread I must have overlooked the very last bullet point in the first post stating they are in stock...Please understand me usually the group buys I took part in once they're gone: they're gone, it's unusual that a group buy organiser takes on the burden to keep extra in stock with the possibility to never sell them, I commend you for that. As soon as my exams are over you will receive a PM with all the relevant info as stated in post n°1. Since you asked; to make it clearer I would emphasize the ()Notes: section in your first post, perhaps having those at the top? Again apologies for that mbrennwa*! Best Regards