Go Back   Home > Forums > > >

Elekit News and products from Elekit

Reply
 
Thread Tools
Old 19th January 2017, 10:51 PM   #1
vkung is offline vkung  Canada
diyAudio Member
 
Join Date: May 2005
Location: Vancouver BC Canada
Default ELEKIT TU-8150

TU-8150
Little brother of TU-8200
●Stock tube : 6005W x 2pcs, 12AX7 x 1pc (option: 6V6 with PCB adaptor)
* 6005W is a highly reliable variation of 6AQ5
●Rated output:  UL connection 2.9W + 2.9W 
Pentode connection 2.9W + 2.9W *8 ohm load for all cases
Triode connection 1.6W + 1.6W
●Rated input :   140mV (INPUT-1) 410mV(INPUT-2) * UL connection
●Residual noise : 75μV rms(IHF-A)
●Frequency response : 20Hz-50kHz(-3dB) 
●Input terminal : INPUT-1(Front)3-pole mini jack (Priority)
INPUT-2(Rear)RCA jack
●Output terminal : SP output terminal (4-8Ω) Binding terminal (banana plug usable)
    HP terminal (8-600Ω 6.3mm standard jack (Not balanced)
●Power voltage : AC120V 50/60Hz (2-slot inlet)  
●Power consumption : 28W *No signal
●Dimensions : W210 x H122.5 x D252mm (incl.projections)
●Weight : Approx.3.5kg (assembled, excl. power cord)

Click the image to open in full size.
Click the image to open in full size.tu-8150

Click the image to open in full size.

Click the image to open in full size.

Click the image to open in full size.

Click the image to open in full size.

Last edited by vkung; 6th October 2021 at 10:37 PM.
  Reply With Quote
Old 20th January 2017, 04:17 AM   #2
EODevan is offline EODevan  United States
diyAudio Member
 
Join Date: Oct 2013
Location: Northwest
Hi Viktor, do you happen to have any pictures of the circuit boards or a size comparison to the TU-8200?

Thanks, and I'm glad to see Elekit putting out so many awesome kits!
  Reply With Quote
Old 20th January 2017, 04:37 AM   #3
vkung is offline vkung  Canada
diyAudio Member
 
Join Date: May 2005
Location: Vancouver BC Canada
I will post some photos later tonight..
The size is half of TU-8200 .. same as the output and weight
  Reply With Quote
Old 20th January 2017, 09:29 PM   #4
EODevan is offline EODevan  United States
diyAudio Member
 
Join Date: Oct 2013
Location: Northwest
While I know it's a hard question to answer, but for headphones only, any preference between TU-882, TU-8200, and the TU-8150?
  Reply With Quote
Old 20th January 2017, 09:38 PM   #5
vkung is offline vkung  Canada
diyAudio Member
 
Join Date: May 2005
Location: Vancouver BC Canada
882/8150/8200
882 is headphone only.. technically it is one of the best headphone amps from Elekit .. ..
For $300, TU-882 is a very good headphone amp.

Last edited by vkung; 3rd February 2017 at 06:00 AM.
  Reply With Quote
Old 5th February 2017, 12:36 AM   #6
nikon f is offline nikon f  United States
diyAudio Member
 
Join Date: Aug 2013
Location: California
How much will the 8150 cost? When will it available?
  Reply With Quote
Old 6th October 2021, 10:16 PM   #7
vkung is offline vkung  Canada
diyAudio Member
 
Join Date: May 2005
Location: Vancouver BC Canada
The new price for TU-8150 is $345.00 (still have 15 units)
  Reply With Quote
Old 6th October 2021, 10:17 PM   #8
vkung is offline vkung  Canada
diyAudio Member
 
Join Date: May 2005
Location: Vancouver BC Canada
Here is the review from Doctor John


Review: Elekit TU-8150(DX), Part I
Doctorjohn Cheaptubeaudio: Audio Reviews and More: Elekit TU-8150 6V6 6AQ5

Comments Let me cut to the chase: this little amp is now my favorite Elekit amp!

Operation Ultra steady. I have it on all day and it barely gets warm.
Sonics It is always hard to describe the sonics of something. For this amp, I would choose Fluent. Many tube amps are easy listening, sometimes referred to as "liquid", but that is not at all the equivalence of fluency, which mandates a good sense of rhythm and superior transparency. Nothing about the TU-8150 grates on you, and everything contributes to keep your interest. Playing disc after disc attests to the superb musicality of this little amplifier with a big heart, neigh, soul!

As Amplifier As with most flea powered amps, particularly if you play vinyl, personally I'd use this with a Preamp to maximize the gain and delivery of the first watt. However, it will sound pretty good as an integrated amp (my System III's Schiit is essentially passive volume). Volume Knob Setting when used as Amp The TU-8150 employs an IC in its preamp section, so it is not just a passive volume knob on an amp. That said, I found not much degradation when the volume knob is maxed out - no overloading or undue hardness. Dialing back may bring a tad more refinement, but the optimal setting is likely dependent on the rest of the system. I have it anywhere between 12:30 and 3:00 Power My YL horns are 104 db, so I have no problems, even with big pieces, as you can read above. I'd think it will work well with loudspeakers over 90 db in sensitivity. Just for the hell of it, I did briefly hooked it up to the LS3/5A, but even with volume knob of both amp and preamp maxed out, there was only moderate volume; however, even then the music sounded nice and lively, not seriously compromised nor muffled, which to me means loudspeaker matching will not be too difficult in general.


As Headphone Amp I think this shall make a very nice headphone amp. But make sure the loudspeakers are connected if you even want to pull out the headphones.

Hybrid? The presence of an op amp in the preamp stage will turn off some tube purists. But I ask myself, do I actually heard sand? Honestly I cannot say I do. The sound is rich and creamy when it is supposedly to. I have heard many all-tube amps that sound a lot more transistory (like German Octave, not to my taste). Elekit has had a long history of using IC/op amp in their products and the designer's skill is apparent.

6AQ5 vs 6V6 In my listening, the 6V6 is unquestionably better. I am staying with 6V6 just because I have a large stash. Although electrically similar, the bigger envelope of the 6V6 likely confers an advantage (just as 6SN7 has it over 6CG7). However, I am equally sure the performance of the 6AQ5 can be much enhanced by rolling in older and better tubes. The suppled GE's are coded 82-52, which is from the very end of 1982, just before tube productions ceased altogether. Older 6AQ5's are plentiful and cheap and one can have fun rolling tubes.

Last edited by vkung; 6th October 2021 at 10:39 PM.
  Reply With Quote
Old 7th October 2021, 09:53 AM   #9
paczeltf is online now paczeltf  Hungary
diyAudio Member
 
Join Date: Jan 2018
Location: Budapest
ELEKIT TU-8150
Quote:
Originally Posted by EODevan View Post
While I know it's a hard question to answer, but for headphones only, any preference between TU-882, TU-8200, and the TU-8150?
I have built the TU-8200 and TU-882.

The 882 uses low power double triodes and has 3 taps on its output transformers. It works the best with low impedance (<80 Ohms) and high sensitivity phones. It is somewhat brighter than the TU-8200, at least with stock tubes.

High impedance phones with more-or-less natural tonal balance sound better via the 8200 to me - much higher driving ability and more mature sound. Note though that I have made significant modifications to the 8200 as I described elsewhere.

A few years ago when it was released, I was considering building the TU-8150 as a secondary headphone amp but then I dropped the idea. Note that even though the factory leaflet may give the impression that the opamp, which is visible on the pictures above, was implemented to amplify the signal from portable devices connected to the jack input, it serves as a driver and is always in the signal path.

I gave the 882 with my old Sony headphones to my friend and he is very happy with them.
  Reply With Quote
Old 13th October 2021, 03:35 AM   #10
rtsang is offline rtsang  Hong Kong
diyAudio Member
 
Join Date: Aug 2005
Hi paczeltf,

I have both the TU-8150 and TU-8800VK. I had used both to drive my Sennheisier HD-650.

The op-amp in the 8150 can be removed as the feedback resistor will act as a signal path to the grid of the 12AX7 driver tube. I had removed the op-amp since day 1 and used it to drive my HD-650 as a desktop amp in my study. More then enough power to drive the headphones as my source is a DAC with full 2V output and low impedance. For purists, one can connect the input directly to the grid of the 12AX7 but I don't want to sabotage my amp.

The 8800 has a much better bass likely due to the bigger transformer (I did upgraded to Lundhal transformers and the output tubes are still 6v6s in UL mode).

Overall I am happy with the 8150 as a headphone amp. 6V6 is a magical tube, with sonic characters very similar to low power DHTs.

I post the cropped section of the schematic of the 8150 showing the op-amp section to illustrate my point. I think this is fair use and should not violate copyright.
Attached Images
File Type: jpg Screen Shot 2021-10-13 at 11.20.17.jpg (57.9 KB, 19 views)
  Reply With Quote

Reply


ELEKIT TU-8150Hide this!Advertise here!
Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Elekit TU-8200 vkung Elekit 1 8th October 2013 05:43 PM
Elekit TU-8100 vkung Elekit 0 19th July 2013 10:40 PM
Elekit TU-8300 vkung Elekit 4 20th March 2010 01:27 AM
Elekit TU-8300 vkung Vendor's Bazaar 0 1st November 2009 03:52 AM
Elekit TU-870 help chrish Tubes / Valves 5 10th June 2008 03:20 AM


New To Site? Need Help?

All times are GMT. The time now is 09:05 PM.


Search Engine Optimisation provided by DragonByte SEO (Pro) - vBulletin Mods & Addons Copyright © 2021 DragonByte Technologies Ltd.
Resources saved on this page: MySQL 13.64%
vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2021 DragonByte Technologies Ltd.
Copyright ©1999-2021 diyAudio
Wiki