Increasing gain to 250mv I now have a sq wave.
C cajones65 Member Joined 2018 2019-12-12 1:10 am #41 2019-12-12 1:10 am #41 Increasing gain to 250mv I now have a sq wave. ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2019-12-12 1:11 am #42 2019-12-12 1:11 am #42 What do you have at the output gates? ••• More options Share C cajones65 Member Joined 2018 2019-12-12 1:20 am #43 2019-12-12 1:20 am #43 Perry to have anything on the gate pads I have to set my scope to 50v 4.00ms and probe set to x1 ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2019-12-12 1:24 am #44 2019-12-12 1:24 am #44 Having it set to the same as when you were looking at the square wave on pin 7, you don't see a signal? Do you now have the 50Hz signal? The low-side will be on the negative rail. The high-side will be at ground level. ••• More options Share C cajones65 Member Joined 2018 2019-12-12 2:21 am #45 2019-12-12 2:21 am #45 Sorry the wife said I had to eat. I do have signals on the pads probe x10 10v 4.00ms Sound comes on when I get the sq waves. ••• More options Share C cajones65 Member Joined 2018 2019-12-12 2:23 am #46 2019-12-12 2:23 am #46 Forgot, I do have the 50hz signal on low side and high side too ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2019-12-12 2:25 am #47 2019-12-12 2:25 am #47 It seems like everything is OK. What, as of now, is the problem? ••• More options Share C cajones65 Member Joined 2018 2019-12-12 2:37 am #48 2019-12-12 2:37 am #48 Fixing to install the outputs and we will hope for the best, thanks Perry. Learned alot about the circuit. ••• More options Share Prev 1 2 3 First Prev 3 of 3 Go to page Go Show hidden low quality content Status This old topic is closed. If you want to reopen this topic, contact a moderator using the "Report Post" button. Share: Facebook Twitter Reddit Pinterest Tumblr WhatsApp Email Share Link Home General Interest Car Audio Renegade RXA1000D
P Perry Babin Member Joined 2003 bcae1.com 2019-12-12 1:11 am #42 2019-12-12 1:11 am #42 What do you have at the output gates? ••• More options Share C cajones65 Member Joined 2018 2019-12-12 1:20 am #43 2019-12-12 1:20 am #43 Perry to have anything on the gate pads I have to set my scope to 50v 4.00ms and probe set to x1 ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2019-12-12 1:24 am #44 2019-12-12 1:24 am #44 Having it set to the same as when you were looking at the square wave on pin 7, you don't see a signal? Do you now have the 50Hz signal? The low-side will be on the negative rail. The high-side will be at ground level. ••• More options Share C cajones65 Member Joined 2018 2019-12-12 2:21 am #45 2019-12-12 2:21 am #45 Sorry the wife said I had to eat. I do have signals on the pads probe x10 10v 4.00ms Sound comes on when I get the sq waves. ••• More options Share C cajones65 Member Joined 2018 2019-12-12 2:23 am #46 2019-12-12 2:23 am #46 Forgot, I do have the 50hz signal on low side and high side too ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2019-12-12 2:25 am #47 2019-12-12 2:25 am #47 It seems like everything is OK. What, as of now, is the problem? ••• More options Share C cajones65 Member Joined 2018 2019-12-12 2:37 am #48 2019-12-12 2:37 am #48 Fixing to install the outputs and we will hope for the best, thanks Perry. Learned alot about the circuit. ••• More options Share Prev 1 2 3 First Prev 3 of 3 Go to page Go Show hidden low quality content Status This old topic is closed. If you want to reopen this topic, contact a moderator using the "Report Post" button. Share: Facebook Twitter Reddit Pinterest Tumblr WhatsApp Email Share Link Home General Interest Car Audio Renegade RXA1000D
C cajones65 Member Joined 2018 2019-12-12 1:20 am #43 2019-12-12 1:20 am #43 Perry to have anything on the gate pads I have to set my scope to 50v 4.00ms and probe set to x1 ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2019-12-12 1:24 am #44 2019-12-12 1:24 am #44 Having it set to the same as when you were looking at the square wave on pin 7, you don't see a signal? Do you now have the 50Hz signal? The low-side will be on the negative rail. The high-side will be at ground level. ••• More options Share C cajones65 Member Joined 2018 2019-12-12 2:21 am #45 2019-12-12 2:21 am #45 Sorry the wife said I had to eat. I do have signals on the pads probe x10 10v 4.00ms Sound comes on when I get the sq waves. ••• More options Share C cajones65 Member Joined 2018 2019-12-12 2:23 am #46 2019-12-12 2:23 am #46 Forgot, I do have the 50hz signal on low side and high side too ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2019-12-12 2:25 am #47 2019-12-12 2:25 am #47 It seems like everything is OK. What, as of now, is the problem? ••• More options Share C cajones65 Member Joined 2018 2019-12-12 2:37 am #48 2019-12-12 2:37 am #48 Fixing to install the outputs and we will hope for the best, thanks Perry. Learned alot about the circuit. ••• More options Share Prev 1 2 3 First Prev 3 of 3 Go to page Go Show hidden low quality content Status This old topic is closed. If you want to reopen this topic, contact a moderator using the "Report Post" button. Share: Facebook Twitter Reddit Pinterest Tumblr WhatsApp Email Share Link
P Perry Babin Member Joined 2003 bcae1.com 2019-12-12 1:24 am #44 2019-12-12 1:24 am #44 Having it set to the same as when you were looking at the square wave on pin 7, you don't see a signal? Do you now have the 50Hz signal? The low-side will be on the negative rail. The high-side will be at ground level. ••• More options Share C cajones65 Member Joined 2018 2019-12-12 2:21 am #45 2019-12-12 2:21 am #45 Sorry the wife said I had to eat. I do have signals on the pads probe x10 10v 4.00ms Sound comes on when I get the sq waves. ••• More options Share C cajones65 Member Joined 2018 2019-12-12 2:23 am #46 2019-12-12 2:23 am #46 Forgot, I do have the 50hz signal on low side and high side too ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2019-12-12 2:25 am #47 2019-12-12 2:25 am #47 It seems like everything is OK. What, as of now, is the problem? ••• More options Share C cajones65 Member Joined 2018 2019-12-12 2:37 am #48 2019-12-12 2:37 am #48 Fixing to install the outputs and we will hope for the best, thanks Perry. Learned alot about the circuit. ••• More options Share Prev 1 2 3 First Prev 3 of 3 Go to page Go Show hidden low quality content Status This old topic is closed. If you want to reopen this topic, contact a moderator using the "Report Post" button. Share: Facebook Twitter Reddit Pinterest Tumblr WhatsApp Email Share Link
Having it set to the same as when you were looking at the square wave on pin 7, you don't see a signal? Do you now have the 50Hz signal? The low-side will be on the negative rail. The high-side will be at ground level.
C cajones65 Member Joined 2018 2019-12-12 2:21 am #45 2019-12-12 2:21 am #45 Sorry the wife said I had to eat. I do have signals on the pads probe x10 10v 4.00ms Sound comes on when I get the sq waves. ••• More options Share C cajones65 Member Joined 2018 2019-12-12 2:23 am #46 2019-12-12 2:23 am #46 Forgot, I do have the 50hz signal on low side and high side too ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2019-12-12 2:25 am #47 2019-12-12 2:25 am #47 It seems like everything is OK. What, as of now, is the problem? ••• More options Share C cajones65 Member Joined 2018 2019-12-12 2:37 am #48 2019-12-12 2:37 am #48 Fixing to install the outputs and we will hope for the best, thanks Perry. Learned alot about the circuit. ••• More options Share Prev 1 2 3 First Prev 3 of 3 Go to page Go Show hidden low quality content Status This old topic is closed. If you want to reopen this topic, contact a moderator using the "Report Post" button. Share: Facebook Twitter Reddit Pinterest Tumblr WhatsApp Email Share Link
Sorry the wife said I had to eat. I do have signals on the pads probe x10 10v 4.00ms Sound comes on when I get the sq waves.
C cajones65 Member Joined 2018 2019-12-12 2:23 am #46 2019-12-12 2:23 am #46 Forgot, I do have the 50hz signal on low side and high side too ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2019-12-12 2:25 am #47 2019-12-12 2:25 am #47 It seems like everything is OK. What, as of now, is the problem? ••• More options Share C cajones65 Member Joined 2018 2019-12-12 2:37 am #48 2019-12-12 2:37 am #48 Fixing to install the outputs and we will hope for the best, thanks Perry. Learned alot about the circuit. ••• More options Share Prev 1 2 3 First Prev 3 of 3 Go to page Go Show hidden low quality content Status This old topic is closed. If you want to reopen this topic, contact a moderator using the "Report Post" button. Share: Facebook Twitter Reddit Pinterest Tumblr WhatsApp Email Share Link
P Perry Babin Member Joined 2003 bcae1.com 2019-12-12 2:25 am #47 2019-12-12 2:25 am #47 It seems like everything is OK. What, as of now, is the problem? ••• More options Share C cajones65 Member Joined 2018 2019-12-12 2:37 am #48 2019-12-12 2:37 am #48 Fixing to install the outputs and we will hope for the best, thanks Perry. Learned alot about the circuit. ••• More options Share Prev 1 2 3 First Prev 3 of 3 Go to page Go Show hidden low quality content Status This old topic is closed. If you want to reopen this topic, contact a moderator using the "Report Post" button.
C cajones65 Member Joined 2018 2019-12-12 2:37 am #48 2019-12-12 2:37 am #48 Fixing to install the outputs and we will hope for the best, thanks Perry. Learned alot about the circuit. ••• More options Share
Fixing to install the outputs and we will hope for the best, thanks Perry. Learned alot about the circuit.