Go Back   Home > Forums > >
Home Forums Rules Articles diyAudio Store Blogs Gallery Wiki Register Donations FAQ Calendar Search Today's Posts Mark Forums Read

Analogue Source Turntables, Tonearms, Cartridges, Phono Stages, Tuners, Tape Recorders, etc.

Chipomatic balanced input RIAA
Chipomatic balanced input RIAA
Please consider donating to help us continue to serve you.

Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving
Reply
 
Thread Tools Search this Thread
Old 10th December 2018, 03:17 AM   #1
Salas is offline Salas  Greece
diyAudio Chief Moderator
 
Salas's Avatar
 
Join Date: Oct 2002
Location: Athens-Greece
Chipomatic balanced input RIAA
Default Chipomatic balanced input RIAA

I was making experiments with INA chips and I put together a relatively few components differential input phono with such. Thought I'd share. Because easy to configure I nicknamed it Chipomatic

U1 is AD8429 which is a low noise instrumentation amplifier of very good general characteristics (SMT only). Texas INA217 (through hole) isn't a bad alternative by the way and it gave about 2.5dB worse noise floor. U2 is half OPA2134 configured as DC servo. R3 C3 values are chosen for mild subsonic filtering also. A passive RIAA equalizes the signal with 20dB loss which is gained back in U3 (the other OPA half) to drive some line preamp. U2 U3 could be done with singles too like the very good LT1792. Should always be a JFET input type due to the passive filter's high source impedance though.

RL1 RL2 are typically 48k total for MM cart or SUT but they would be optimum at 750R each for the AD's input current noise. When driven from say a DENON DL-110 of 160 Ohm source impedance, 1k each is doable for instance. Measuring 3dB better.
If the SUT has a middle tap on its secondary the GND point should be moved there than between RL1 RL2 to improve SNR due to less impedance for U1's input bias currents.

With the ~50R RG shown there's 42dB gain. Good for 2.5mV HMC. Adding 20dB voltage gain with a 10X step up transformer, or with an active differential pre-pre stage, its good for 0.25mV LMC. The noise floor goes up by 10dB in that case.

RG=63R gives 40dB gain and RG=100R 36dB gain for 3mV-5mV MM cartridges. 36dB & 10X SUT is good for 0.5mV MC. Output goal is about 300mV RMS nominal at 5cm/sec velocity with all types of cartridges and suitable gains.

I measured 28V pk-pk non clipped output at 1kHz with +/-15V rails thus 30dB overload margin above nominal output.

After breadboard phase I constructed a little matrix board monophonic example for 42dB. Its not best because it takes proper PCB of expert layout with ground plane and copper fill in such gains, especially for high performance chips, but its rather passable as proof of concept. To help against too much hum pick up I rested it on grounded metallized paper from a pack of cigarettes

Anyways, I managed some FR & SPA measurements (using SE signal source and a balanced impedance divider). Showing its RIAA transfer curve, its conformity to flat with software anti-RIAA, and 1kHz 500mV RMS output level FFT for its THD. Also (added later) 1VRMS FFT at 62dB total gain by the addition of 20dB SUT when running on SMPS supplies to avoid mains interference spikes in the grass. Technically not too shabby results I would say. Given the configuration practicality and the matrix build I mean. Acoustically I don't know, I will have to either make yet another matrix channel or a decent printed board and listen to it some day in the near future to let you know. Hey I even have a tube output stage option designed already with 6DJ8 (E88CC) instead of U3
Attached Images
File Type: png CmaticSCH.png (17.9 KB, 1066 views)
File Type: png CmaticRIAA.png (19.9 KB, 1075 views)
File Type: png CmaticFR.png (17.0 KB, 992 views)
File Type: png CmaticTHD.png (21.8 KB, 992 views)
File Type: jpg CmaticFRV.jpg (429.4 KB, 954 views)
File Type: jpg CmaticBAV.jpg (497.4 KB, 293 views)
File Type: jpg CmaticTest.jpg (428.8 KB, 201 views)
File Type: jpg CmaticTest2.jpg (409.1 KB, 216 views)
File Type: jpg Cmatic2smps.jpg (572.9 KB, 148 views)
File Type: png Img.png (55.8 KB, 147 views)
  Reply With Quote
Old 10th December 2018, 03:37 AM   #2
6L6 is offline 6L6  United States
diyAudio Moderator
 
6L6's Avatar
 
Join Date: Oct 2010
Location: Denver, Colorado
Chipomatic balanced input RIAA
Your 'Folded Simplistic Phono' is amongst the very best RIAA I've ever heard, I fully expect this to be wonderful as well!!

Looking forward to a PCB.
  Reply With Quote
Old 10th December 2018, 03:53 AM   #3
Salas is offline Salas  Greece
diyAudio Chief Moderator
 
Salas's Avatar
 
Join Date: Oct 2002
Location: Athens-Greece
Chipomatic balanced input RIAA
Have you got balanced output TT leads or balanced impedance SUT though? I don't know how those INA chips sound yet, just made it for technical practice. The FSP I am informed it will sound significantly better if with UltraBiB incorporated. A member reported that. Will have to revise it for V1.3 onboard shunts at a point.
  Reply With Quote
Old 10th December 2018, 04:47 AM   #4
Calvin is offline Calvin  Germany
diyAudio Member
 
Calvin's Avatar
 
Join Date: Nov 2004
Location: close to Basel
Hi,

of course can it be wonderful.
Its almost a PlatINA, RG1, Calvin-Phono or one of the several other inkarnations of this theme, that mostly utilize a THAT or TI INA. ;-)
If You wanna know how those INA Phonos can sound ... just read one of the many threads or reviews of clearaudio balanced stages et al *lol*

jauu
Calvin
  Reply With Quote
Old 10th December 2018, 05:14 AM   #5
Salas is offline Salas  Greece
diyAudio Chief Moderator
 
Salas's Avatar
 
Join Date: Oct 2002
Location: Athens-Greece
Chipomatic balanced input RIAA
Hey! So you have done such stuff and you guarantee its good. Lets spoil the chips by mixing tube buzzes on output then
Attached Images
File Type: png CmaticTubeSCH.png (28.4 KB, 442 views)
  Reply With Quote
Old 10th December 2018, 05:44 AM   #6
The Space Egg Corp is offline The Space Egg Corp  England
diyAudio Member
 
The Space Egg Corp's Avatar
 
Join Date: Sep 2010
Location: London & Miami
Cool Another C O O L bit of solder slingin' !

.

Hi Salas


Nice bit of solder slingin'

Can I have some chips with that please.


One of the best things you can do with a turntable ...

... is to put some low-capacitance microphone-cable & nice gold-pinned XLR-plugs on it.


The only problem is ... then you can't plug it in to any of your kit.

I guess that's why you never see folks doing that.


Do I really want to plug my Thorens into my Stanton pro D.J. phono-amp/mixer though ? ...

... No !


Balanced is very tempting for the intrepid plastic-spinner !

But it seems that few take the plunge.


I'm surprissed that we haven't seen many balanced 'Simplistics'.

Merlin/Fellipes nice balanced 'Simplistic' was an inspiration to my u l t r a s l o w slingin'.


The circuit looks like a great one & simple as well.

Keep that junction-count L O W mmaann . . .


Go on folks ... Take the PLUNGE and hack oorrff those outmoded ancient RCA plugs.

You KNOW it makes perfect sense.


Si.

t.S.E.c

.
  Reply With Quote
Old 10th December 2018, 06:44 AM   #7
Salas is offline Salas  Greece
diyAudio Chief Moderator
 
Salas's Avatar
 
Join Date: Oct 2002
Location: Athens-Greece
Chipomatic balanced input RIAA
Can be made SE input if grounding at the (-in) instead but that's wimpy. I didn't measure too good SNR for more than 50dB gain with just INA as well. Some SUT or diff pre pre is definitely needed for well done MC.
  Reply With Quote
Old 10th December 2018, 02:27 PM   #8
billshurv is offline billshurv  United Kingdom
diyAudio Member
 
billshurv's Avatar
 
Join Date: Mar 2014
Chipomatic balanced input RIAA
Don't forget that MM cartridges have one pin connected to the case of the cartridge. To run balanced you need to ideally disconnect that and run a 5th wire, which puts a lot of people off balanced MM phono. I can live with that, but have transcended voltage amplifiers for my MM needs
  Reply With Quote
Old 11th December 2018, 01:41 AM   #9
Salas is offline Salas  Greece
diyAudio Chief Moderator
 
Salas's Avatar
 
Join Date: Oct 2002
Location: Athens-Greece
Chipomatic balanced input RIAA
Using shorter test cables and moving it about a bit cleans up further and the 50Hz hum spike is almost gone. Other related spikes probably from the lab supply's interference remain. I replaced the graph for 0.5V RMS THD in post#1. Interestingly at 1VRMS the second and third harmonic rise equally. Fortunately not only third for program peaks then.
Attached Images
File Type: png CmaticTHD_1VRMS.png (21.7 KB, 438 views)
  Reply With Quote
Old 11th December 2018, 02:15 AM   #10
scott wurcer is offline scott wurcer  United States
diyAudio Member
 
scott wurcer's Avatar
 
Join Date: Jan 2004
Location: Belmont MA
Quote:
Originally Posted by Salas View Post
I was making experiments with INA chips and I put together a relatively few components differential input phono with such. Thought I'd share. Because easy to configure I nicknamed it Chipomatic
My goodness Salas does 8-legs, if you want to try a couple of gold plated DIP's just ask.
__________________
"The question of who is right and who is wrong has seemed to me always too small to be worth a moment's thought, while the question of what is right and what is wrong has seemed all-important."
  Reply With Quote

Reply


Chipomatic balanced input RIAAHide this!Advertise here!
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
RIAA Head Amp Models (Phono Preamp) with only balanced XLR-Cannon Input Sockets tiefbassuebertr Analogue Source 8 27th April 2016 02:17 AM
Balanced input all DC coupled RIAA preamp FdW Analogue Source 167 28th April 2015 01:41 PM
Two balanced line receivers (switched) at one balanced input barcley Analog Line Level 4 7th April 2015 11:47 AM
balanced RIAA amp musitronix Tubes / Valves 0 19th May 2011 02:02 AM
How Can I connect A Balanced RIAA Phono Pre-Amp to a Phono Plug amp input jmartinbaugh Analogue Source 3 25th April 2011 01:24 PM


New To Site? Need Help?

All times are GMT. The time now is 04:37 AM.


Search Engine Optimisation provided by DragonByte SEO (Pro) - vBulletin Mods & Addons Copyright © 2019 DragonByte Technologies Ltd.
Resources saved on this page: MySQL 15.00%
vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2019 DragonByte Technologies Ltd.
Copyright ©1999-2019 diyAudio
Wiki