Has a necrophilic ring to it, imo
.
Attachments
won't lemme see the things sez need proof of AGE😕
Just type in 99 Words for Boob's song into search engine - it's bound to show up somewhere.
Last edited:
www.youtube.com/watch
(the chances of Thomas leaving this galaxy as a result of dehydration in front of the PC are increasing by the day)
(the chances of Thomas leaving this galaxy as a result of dehydration in front of the PC are increasing by the day)
I dunno why I get an erection every time I watch this sexy dude https://www.youtube.com/watch?v=ir7GZFJGmI0&t=23
I dunno why I get an erection every time I watch this sexy dude https://www.youtube.com/watch?v=ir7GZFJGmI0&t=23
When I went to watch that video I spotted this one there too..... 😀😀😀
https://www.youtube.com/watch?v=6l6sty6SFVo
Attachments
I dunno why I get an erection every time I watch this sexy dude https://www.youtube.com/watch?v=ir7GZFJGmI0&t=23
I get erection every time i think about being first one to build T.T.T.A.
Turn table tangential Arm whit Pyrolitic Graphite unt magnet bearings and almost every time I do not
Whats the heat conductivity on a dachshund?
About 107f degrees - a couple of those keep me nice and toasty kicked back in my reclining chair.... 😀😀😀
Attachments
Last edited:
And for the zumba master: Today we fixed the gas and oiltank attachments to the frame, cut the rear fender to 180 degrees and took it all apart again for a new blow job with paint, no pix
And for the zumba master: Today we fixed the gas and oiltank attachments to the frame, cut the rear fender to 180 degrees and took it all apart again for a new blow job with paint, no pix
ook ..... nice to hear that there's a progress
mine Tinker Bell is progressing too
some work around camshaft finished ,
carbs split from two to one , new inlet manifold ,
new boxes for battery, electric and tool ,
new seat ready for upholstering ,
tank , front fender and new back fender with new mounting hardware are at paint shop ,
speedo case and mounting on risers ,
shock silent blocks redone from bearing plastic ,
new mufflers made of SS,
new bearings for back end
still some work to do - mainly on wiring and some mechanical
practically - barring engine case , every bolt was dismantled and inspected .... in the end it would be much different to HD wanabee as it started from factory ...... except few bearings and chain/sprocket set , everything new will be strictly DIY
will put some info and few pics in my blog , as soon I finish ..... in a month , hopefully
Attachments
It is looking good ZM. Just in time for riding season.
Last pic?
Dodo, is there 2 fullsize Samsonite and a cabin bag under the seat? Lookkking goud. Bet u will kick b4 I do. Cheers dodos.ook ..... nice to hear that there's a progress
mine Tinker Bell is progressing too
some work around camshaft finished ,
carbs split from two to one , new inlet manifold ,
new boxes for battery, electric and tool ,
new seat ready for upholstering ,
tank , front fender and new back fender with new mounting hardware are at paint shop ,
speedo case and mounting on risers ,
shock silent blocks redone from bearing plastic ,
new mufflers made of SS,
new bearings for back end
still some work to do - mainly on wiring and some mechanical
practically - barring engine case , every bolt was dismantled and inspected .... in the end it would be much different to HD wanabee as it started from factory ...... except few bearings and chain/sprocket set , everything new will be strictly DIY
will put some info and few pics in my blog , as soon I finish ..... in a month , hopefully
- Home
- Amplifiers
- Pass Labs
- The Pass Pub: The High-End Off Topic Thread