I bought them from batteryspace.com
LiFePO4 26650 Battery:12.8V 3300 mAh (42Wh, 7A rate) w. PCB
I also bought a battery charger especially designed for these lifepo4 batteries
Smart Charger (1.5A) for 12.8 V LiFePO4 battery Pack (4 cells,15.2V cut-off) with 5.5mm x2.1mm Male Barrel plug-- CE / UL listed
I have been searhing for them in europe to but couldn't find them anywhere.
Okey, I thought a "normal" solar charge controller would work.
As you all noticed I'm not an expert of this.
Is it possible to connect 2 of these 10W, 12V solar panels (24 volt) to the charge controller you linked?
The reason I go with lifepo4 batteries and not SLA batteries is because they are forbidden in some festivals in sweden, so SLA is not an option for me.
That was what I did with my 12V 18AH battery.
Easier to just throw the switch to kill power consumption.
Easier to just throw the switch to kill power consumption.
One of those panels, or two of them in parallel, will work with that controller. They call it a "12V" panel, but it's maximum power point is actually 17V!
4 Pcs Piezo Tweeters Replacement for Motorola KSN1001A
They write that thse are the exact similar Piezos as the original Saturnus used.. can any one confirm that? it seems wierd cause those are 4 for 18 dollars.. an the here Martin Sound its 1 for 23?
They write that thse are the exact similar Piezos as the original Saturnus used.. can any one confirm that? it seems wierd cause those are 4 for 18 dollars.. an the here Martin Sound its 1 for 23?
Those you are linking to are replacements tweeters, so they're only a replica of the original. The physical specifications may be the same, but i doubt that the sound quality is as good as the Motorola/CTS originals.
They might have similiar specifications (as in frequency range and sensitivity), but the sound is totally different. The Motorolas/CTS tweeters are simply just of much higher quality in all aspects.
okay.. im getting these parts on x-mas eve:
2x HP-10w
1x Amp6basic
2x QLM-1005 Piezos
and then two of these bassreflex tubes
If the 2 last parts arrent going to be that good then i'll just buy some others that are better.. its not that expensive..
I've read that the QLM-1005 will need some 33 or 47 ohm resistors with 3w .. could i use these then? and how many? RES .47 OHM 3W 5% METAL OXIDE - ERX-3SJR47
2x HP-10w
1x Amp6basic
2x QLM-1005 Piezos
and then two of these bassreflex tubes
If the 2 last parts arrent going to be that good then i'll just buy some others that are better.. its not that expensive..
I've read that the QLM-1005 will need some 33 or 47 ohm resistors with 3w .. could i use these then? and how many? RES .47 OHM 3W 5% METAL OXIDE - ERX-3SJR47
One per piezo so 2 in total for the staggering amount of 1 dollar. Find out everything else you need to buy at Digikey so that you can buy it all at once.
i have no idea what i else has to buy :b hehe, but i might order some extra resistors 😉
Saturnus, i cant remember if it was you who wrote something about at thing that would make the sound'siglna' from the ipod or PC louder and deeper.. It was a thing that you connect like this..
aux cabel from pc/ipod ect. into that little thing --> aux cable from the little thing to amp or headphone .. if you understand?
Saturnus, i cant remember if it was you who wrote something about at thing that would make the sound'siglna' from the ipod or PC louder and deeper.. It was a thing that you connect like this..
aux cabel from pc/ipod ect. into that little thing --> aux cable from the little thing to amp or headphone .. if you understand?
Be aware of the dot before the number 47. 😉 The resistor you link to has a resistance of 0.47 ohm.
So now we've finally recieved our solar panels, and though they have a perfect length of 915 mm the width is 305 mm, which is 5 mm too much.. is there any smart way of fixing this little issue so that it still will look good and not have a sharp edge ?
think i've found some? http://dk.farnell.com/yageo-phycomp/pnp3wvjt-73-47r/resistor-3w-5-47r/dp/1779314 ?? should they be in carbon or
Last edited:
Nope. Those are not metal film but wire wound. Same place same price
MULTICOMP|MOR03SJ0470A19|RESISTOR, 3W 5% 47R | Farnell Danmark
thank you very much! then it looks like iv'e evrything i need 😉 might need a little advice when im coing to connect the resistors ect.
Saturnus, is it a big problem that im getting HP-10w in 8 ohm instead of 4ohm? .. no 4ohms on the market 🙁
You are supposed to get the 8 Ohm version of the HP-10W when using the AMP6 or equivalent.