Pelagus res est ut sit verus et linguae historia de essentia, nec lobortis erat non mauris.amicus Plato, sed magis amica veritas.
Where do you find this...
A lay-press article: On the Face of It: The Psychology of Electability | The New Yorker
EDIT: Another article: What Your Face Really Reveals About You | Psychology Today
Last edited:
Gunfu, I am sure there are huge optical differences between those cables.
You're missing the trick. The "high-end" "Audiophile" cables often (intentionally!) add enough capacitance and inductance to make measurable and audible differences, and if there's an audible difference, the more expensive one must be better!Pretty much any cable will do 0-20kHz from a stable source into a reasonable impedance without creating measurable artifacts, regardless of it being used for audio or whatever. I am with Peter Walker on this one.
...and if there's an audible difference, the more expensive one must be better!
True for some people who don't listen carefully. Another way of putting it is that 'they don't check,' meaning that they don't carefully A/B multiple times to see if an initial impression holds up under more careful subjective scrutiny.
Benb, I see that you are fantasizing, just take and compare several audio cables from each other. You will begin to hate yourself and consider yourself a village. Does different beer taste the same?
Last edited:
I'm beginning to wonder if parallels can so readily be draw between perceptions of speech and music? I'm certain they can't be drawn between cables and beer 🙄
For you from Wales, I would write that all grades of whiskey are the same? Do you think this is so?
I think you all missed Ohm's law. He says that the current through a non-linear load will also always be non-linear, which means that the voltage drop across the conductors will also be non-linear, which is already distortion at the speaker terminals.
https://audio-database.com/AUREX/amp/sc-lambda90f(11).JPG
I think you all missed Ohm's law. He says that the current through a non-linear load will also always be non-linear, which means that the voltage drop across the conductors will also be non-linear, which is already distortion at the speaker terminals.
https://audio-database.com/AUREX/amp/sc-lambda90f(11).JPG
Last edited:
It was my wife’s bod that attracted me. Of course she has a fine mind as a university educated psychologist and she turned heads whenever we went out. She still does.
After I shaved my hair off because I could not get to a barber In time because of this Covid thang, my siblings told me I looked like a criminal.
Finally, at 63 I have street cred.
After I shaved my hair off because I could not get to a barber In time because of this Covid thang, my siblings told me I looked like a criminal.
Finally, at 63 I have street cred.
I'm having one of my hunts for records with better dynamics and, as part of the analysis wanted to measure crest factor. Foobar DR plugin gives an RMS to peak measurement across a whole track but that doesn't give a full picture. Made me think, how long a period do you use to calculate crest factor and does it actually make any sense as a metric with real music?
CoolEdit lets you select the time window and it makes a big difference. IMHO this makes me skeptical of some of the purported DNR measuring tools. For a given time window there will be a distribution of crest factors, with random noise these can be computed. Bill did you think you could slip in a real technical issue here?
Last edited:
Where do you find this crap?
Favorite of 60's comic book artists.
Attachments
Sure.Esoteric means enigmatic, hermetic, something beyond the understandings proved in sciences.
Well, BS says it all.

For you from Wales, I would write that all grades of whiskey are the same? Do you think this is so?
I think you all missed Ohm's law. He says that the current through a non-linear load will also always be non-linear, which means that the voltage drop across the conductors will also be non-linear, which is already distortion at the speaker terminals.
https://audio-database.com/AUREX/amp/sc-lambda90f(11).JPG
Even if the load displays a non-linear V/I characteristic, the wire driving it will display a linear I*R characteristic. Unless it doesn't, in which case it is not a wire.
Cheers!
Howie
Yes, only you are confused again, load resistance and wire resistance are two different things. And the current flows through them the same i.e. common. This problem can only be for third-grade students who have not yet studied Ohm's law for nonlinear circuits, and not for an engineer.Even if the load displays a non-linear V/I characteristic, the wire driving it will display a linear I*R characteristic. Unless it doesn't, in which case it is not a wire.
Cheers!
Howie
Cheers!
Last edited:
Yes, only you are confused again, load resistance and wire resistance are two different things. And the current flows through them the same i.e. common. This problem can only be for third-grade students who have not yet studied Ohm's law for nonlinear circuits, and not for an engineer.
Cheers!
Insults aside, I assumed you were saying that the wire displayed non-linear behavior, which, if it is made of copper it does not, no matter what load it is connected to, linear or not.
Howie
On the other hand, their X01 D2 CD/SACD player from a few years back used four PCM1704 D/A chips and seven OPA627 per channel (!), And WBT NextGen connectors. Go figure.Their top of the range preamp uses a PGA2310.
Shock! horror.
I never said such a thing, it’s all your own time you invented and inspired yourself to justify not the influence of audio cables on distortion.Insults aside, I assumed you were saying that the wire displayed non-linear behavior, which, if it is made of copper it does not, no matter what load it is connected to, linear or not.
Howie
Insults aside, I assumed you were saying that the wire displayed non-linear behavior, which, if it is made of copper it does not, no matter what load it is connected to, linear or not.
Howie
Around here you need to be careful or someone will start talking about 200A and #14 wire (copper is about 3000ppm/degree C).
I never said such a thing, it’s all your own time you invented and inspired yourself to justify not the influence of audio cables on distortion.
We must have a language barrier issue here, apparently neither of us accurately communicated to the other, my apologies.
Howie
Here is another who does not know Ohm's law. I have long suspected that those who deny the influence of cables do not know the most basic things. Therefore, they are so deeply swallow this bait. The Japanese are aware of this.Around here you need to be careful or someone will start talking about 200A and #14 wire (copper is about 3000ppm/degree C).
https://audio-database.com/AUREX/amp/sc-lambda90f(11).JPG
Last edited:
- Home
- Member Areas
- The Lounge
- The Black Hole......