http://www.diyaudio.com/forums/members/martin-martinez.htmllooks good with the PCB, any plans to sell them?
i don't plan to sell it.. just for collection on my work space. because i'm glad to try something new. if there are relatives who want it, i will give it.
again
can you try again to take a picture, kinda hard to see how it looks.
OK!
This is very good! I have to thank you and everyone...
having a broken tda and another defunct (suspect) tda,
went for this: LM3886 +sc5200sa1943...
and its very nice sounding right now.
Getting better ...
followed the schematic by Mr Feuerbacher, and added 1k input r,
didnot use local C but the 4x4700uf from the PS just the NPelec 2uf
beetwen +and- at the bipolar-chip node
maybe later i´ll try some nf´s to snubber the xfrmer or th bridge.
ithink its kind of bright if something maybe alittle on the edge at both ends, but nice and certainly flatter than some.
have to make voltage reducer with res and zenners for the mic section and the eq. also for the mp3 reproducer need like 12V
first pic: amp left , right is eq and behind mic input line input..
2nd: amp
3rd: xover
4th: amp
5.: chip
6th: wheres my glasses??
This is very good! I have to thank you and everyone...
having a broken tda and another defunct (suspect) tda,
went for this: LM3886 +sc5200sa1943...
and its very nice sounding right now.
Getting better ...
followed the schematic by Mr Feuerbacher, and added 1k input r,
didnot use local C but the 4x4700uf from the PS just the NPelec 2uf
beetwen +and- at the bipolar-chip node
maybe later i´ll try some nf´s to snubber the xfrmer or th bridge.
ithink its kind of bright if something maybe alittle on the edge at both ends, but nice and certainly flatter than some.
have to make voltage reducer with res and zenners for the mic section and the eq. also for the mp3 reproducer need like 12V
first pic: amp left , right is eq and behind mic input line input..
2nd: amp
3rd: xover
4th: amp
5.: chip
6th: wheres my glasses??
Attachments
Last edited:
now idont wanna letitgo!
have to make abiiig big BIGONE
yeah maybe double pairof transistors and bridged....
have to make abiiig big BIGONE
yeah maybe double pairof transistors and bridged....
yes!
after a few hours shouting lots of different music, it is
now alittle bit more relaxed, less edgy and takes good care of low frequency. It is running warm
after a few hours shouting lots of different music, it is
now alittle bit more relaxed, less edgy and takes good care of low frequency. It is running warm
Attachments
Last edited:
there´s actually two 3886, and one is made with 22k-1k-47uf string,
the other, in use, is just 22k-1k no fbcap!
Used that before and less is more?
or else...
i´ll test drive vers 2. jejeje
letyou know later after all this mess is up and running.
Sorry, those two pics from my job!
the other, in use, is just 22k-1k no fbcap!
Used that before and less is more?
or else...
i´ll test drive vers 2. jejeje
letyou know later after all this mess is up and running.
Sorry, those two pics from my job!
Last edited:
have to make abiiig big BIGONE
WORK is in progress to make a big one 3 pairs per channel and bridged
warm regards
andrew lebon
WORK is in progress to make a big one 3 pairs per channel and bridged
warm regards
andrew lebon
hey mr Andrew...
shure would like totry that too!
and, what PS willyou be using with it?
I have two big chunks of iron
like 80+80 secundaries like 1kva
those really need a soft start.
the 3886 is ok still sounding loud and clear
using it alone, without pre and eq
eqed alittle from the lap´s wmp
full output sounds alittle ragged but must be the lap output rather than the amp
shure would like totry that too!
and, what PS willyou be using with it?
I have two big chunks of iron
like 80+80 secundaries like 1kva
those really need a soft start.
the 3886 is ok still sounding loud and clear
using it alone, without pre and eq
eqed alittle from the lap´s wmp
full output sounds alittle ragged but must be the lap output rather than the amp
Attachments
Last edited:
Can someone please tell me how much can i pull out for two 4ohm woofers from a single chip tda7293 and transistors from a 25-0-25 200va transformers? and in which configuration? series or paralell without making new boards?
Sorry im a noob... and
Thank you!
Sorry im a noob... and
Thank you!
Thank you 🙂
An externally hosted image should be here but it was not working when we last tested it.
Could anyone please explain the how is this being powered?
I'm new to this stuff, so...
Thanks anyways.
this thing really gets better!, isit sort of stabilizing or something ?
this the so called burn in?
the first clone i made didnot improve much the first ten or more hours
don´t know now, have to listen to it.
But this one when augmented with the transistors, started sounding kind of bad and was having trouble with a bad speaker, after changing to another bigger and more power withstanding speaker, left it for two hours full volume from laptop, then came and lowered for half hour and again full for four hours it got better and more today.
would like to measure but dont have the equipment
this the so called burn in?
the first clone i made didnot improve much the first ten or more hours
don´t know now, have to listen to it.
But this one when augmented with the transistors, started sounding kind of bad and was having trouble with a bad speaker, after changing to another bigger and more power withstanding speaker, left it for two hours full volume from laptop, then came and lowered for half hour and again full for four hours it got better and more today.
would like to measure but dont have the equipment
what did you do martin martinez, in my experience with several of these amps over that last 5 years is that they sound awesome from 1 second and the same 5 years later??, are you using some old caps that are leaking or something??
But im glad that some of you are finally using this AMP, it is still the best i owned
But im glad that some of you are finally using this AMP, it is still the best i owned
Thanks for your comments! and sharing.
This clone sounded not to good until reinforced with the transistors
and- also rearranged cables, grounds included,-
at every time i came to listen, turned it off discharged caps
and moved this and that ,turn on and listen
loud and quiet, get away some more time... etc.
This clone sounded not to good until reinforced with the transistors
and- also rearranged cables, grounds included,-
at every time i came to listen, turned it off discharged caps
and moved this and that ,turn on and listen
loud and quiet, get away some more time... etc.
I was going to do this with my single sided LM3886 PCB and added 2 pairs
Is it even possible? seems like it is but i belive it may sound not as good 🙁
If it sounds good I will do it it will cost around 80€ just to make 2PCBs with mid qualty
components...
how to take screenshots
ITS NOT FINISHED BOARD.
Few more things to do but, heall yeah its going to kick butt, at least i think 🙂
Is it even possible? seems like it is but i belive it may sound not as good 🙁
If it sounds good I will do it it will cost around 80€ just to make 2PCBs with mid qualty
components...
An externally hosted image should be here but it was not working when we last tested it.
how to take screenshots
ITS NOT FINISHED BOARD.
Few more things to do but, heall yeah its going to kick butt, at least i think 🙂
Ahan, could i please have a scematic for the PSU?usman... i use 25-0-25 transformer(125VA), one
15amp bridge rectifier, and 4x4700uF caps.
- Home
- Amplifiers
- Chip Amps
- TDA7294 + Power Transistors AMP (TDA7293 to come also)