Some speaker driver measurements...

Jump to Latest
#202
Excellent driver. Just finished a 2-way with the silver version of it, sounds fantastic! Good response down into the 30s. Biggest weakness I found is that max volume before it bottoms out is fairly low, so it'd be dangerous to use it on content with loud low frequency content.
 
#205
HiFiCompass said:
Thanks to generosity of one forum member from US which donated midwoofer SB15NBAC30-4 for testing we can see the measurements of that excellent speaker:

SB Acoustics SB15NBAC30-4 | HiFiCompass

Probably out of modesty, that guy didn't want that his name be known for community.
Click to expand...


First cone break-up mode far away at 9kHz falling into area of dustcap break-up mode, smooth and flat impedance rise without signs of internal reflections or structural resonances, lowest HD in critical 1-3k range, no HD exploding on higher voltages, silent CSD, on the other hand, only acceptable sensitivity giving its Re of 3.1 Ohm and a little bit off-axis problems due to pistonic hard cone and tallish surround (why still single-roll is used in domestic audio?) But most importantly, it is CHEAP! Great great driver.
 
Last edited:
#208
It is interesting how the SBA Satori woofer version (MW16P-8) shows lower overall distortion than the midrange version (MR16P-4), especially if you are considering 2nd order slopes to a woofer in a 3 way ~ 200Hz crossover - with an extra 2mm xmax. Allowing for the 4 ohm difference, I estimate you are only losing ~ 1dB sensitivity.

It looks on paper that the woofer, is a better wideband upper bass / midrange driver than the midrange version?
 
#209
Windforce85 said:
First cone break-up mode far away at 9kHz falling into area of dustcap break-up mode, smooth and flat impedance rise without signs of internal reflections or structural resonances, lowest HD in critical 1-3k range, no HD exploding on higher voltages, silent CSD, on the other hand, only acceptable sensitivity giving its Re of 3.1 Ohm and a little bit off-axis problems due to pistonic hard cone and tallish surround (why still single-roll is used in domestic audio?) But most importantly, it is CHEAP! Great great driver.
Click to expand...

I use the 8 ohm version in an open baffle ( even though the sensitivity is rather low) the clarity of this driver is just remarkable once one has notched out the peaks at the upper end. An amazing driver for the price.

C.M
 
#212
wow, the 5th order almost does not move.
its only issue seem:
-lots of energy stored around 9.5K (see waterfall), meaning high lowpass order and/or low cross over points are necessary.
I am not sure if the 3rd order harmonic peak at 3k is harmful.
In any case, I d try a second order LP 1800Hz with a solid tweet.
 
#213
Martigane said:
wow, the 5th order almost does not move.
its only issue seem:
-lots of energy stored around 9.5K (see waterfall), meaning high lowpass order and/or low cross over points are necessary.
I am not sure if the 3rd order harmonic peak at 3k is harmful.
In any case, I d try a second order LP 1800Hz with a solid tweet.
Click to expand...

I did 3 kHz 4th order and 2.5 kHz 4th order for C90-6-724 in my different systems and have to say 2.5/4 sounds better.
 
#215
Martigane said:
wow, the 5th order almost does not move.
its only issue seem:
-lots of energy stored around 9.5K (see waterfall), meaning high lowpass order and/or low cross over points are necessary.
Click to expand...
Yeah, it's definitely not a plus, but at the same time, no one should be using a mid of that size up high enough where the fundamental or any of the significant harmonics would be reproducing audible, distinguishable music at that frequency.
 
You must log in or register to reply here.
Top Bottom