rowemeister said:
Is this new since fitting the clock feed? or an old problem?
Have you screened the chips with copper foil? also the new circuit?
poynton said:
It since fitting pcb, I will be screening chip and fitting it next to servo ic.
I chucked it all together to test, a little more care in the fitment etc and it should be ok.
Brent
poynton said:
It is something I had thought of.
I really want to get it right as the benefits are very good.
Brent
oooooo
My Russ Andrews Oak cone feet have arrived.
The Oak is very good quality too, very hard indeed.
Brent
My Russ Andrews Oak cone feet have arrived.
The Oak is very good quality too, very hard indeed.
Brent
just a thought
could be echo's
or
which one Dac or decoder is the master?
being
if your have the clock as set
the decoder and dac has to sync to the clock
if the clock is signal is interrupted to either the dac or decoder.
then data will be out of sync.
might be why the companies put the clock on the dac then run the decoder of the dac.????
allan
ps interruption could be anything ie RF, EMF, Vibration even down to
to cables?
could be echo's
or
which one Dac or decoder is the master?
being
if your have the clock as set
the decoder and dac has to sync to the clock
if the clock is signal is interrupted to either the dac or decoder.
then data will be out of sync.
might be why the companies put the clock on the dac then run the decoder of the dac.????
allan
ps interruption could be anything ie RF, EMF, Vibration even down to
to cables?
rowemeister said:
Yep
I may also try tapping off the decoder feed.
Brent
where is it put into the decoder?
allan
Morning all, thanks for the compliments, lol
Had a little listen to Joni Mitchell Hits this morning and I can now hear her sing "...he did the goat dance very well, but he kept my camera to sell." That last bit had never been decipherable before, a bit blurred on the last few words. I can only imagine what sort of clarity and detail Brent's player digs up with all those low noise regs
Simon
Had a little listen to Joni Mitchell Hits this morning and I can now hear her sing "...he did the goat dance very well, but he kept my camera to sell." That last bit had never been decipherable before, a bit blurred on the last few words. I can only imagine what sort of clarity and detail Brent's player digs up with all those low noise regs
Simon
SimontY said:Morning all, thanks for the compliments, lol
Had a little listen to Joni Mitchell Hits this morning and I can now hear her sing "...he did the goat dance very well, but he kept my camera to sell." That last bit had never been decipherable before, a bit blurred on the last few words. I can only imagine what sort of clarity and detail Brent's player digs up with all those low noise regs
Simon
Excellent.
Yes I must admit the player does sound well
Brent
rowemeister said:
Excellent.
Yes I must admit the player does sound well
Brent
I bet
Btw, I estimate the cost of my reg mod to be approximately £3.50. Obviously it takes a lot of thought and time for someone with no electronics knowledge to complete, but otherwise, what value!!
awpagan said:
Same coax yes. The Dac to decoder coax has been in use for a few months now.
Brent
rowemeister said:
I was thinking RF induced earth loop
Is the coax earth at the decoder as well?
allan
ps as for the display
ask simon here's the expert in that😀
awpagan said:
ps as for the display
ask simon here's the expert in that😀
lol. Oh yes, the expert in breaking it!! Mine is still dead!!
😕 
SimontY said:
lol. Oh yes, the expert in breaking it!! Mine is still dead!!
sorry simon
i thought you fixed it
allan
I gave up! lol. Tried some different parts and checked various points and showed voltages, but it got me nowhere. It plays music, and that's all that matters.