Hallo,
I'm a new member. I'm looking for a circuit or schematic plan for the kenwood basic c2 preamp and kenwood basic m2 amp. A few weeks ago i bought a c2 and its sound is very good. Now i'm looking for a m2, but all i've found was defect amps. I suppose the powercircuits dat 1521 and/or dat 1018 have finished there life...
I've red that there is a posibility to bypass the TA2031 and than the amp maybe runs fine ... only that it runs real hot! Maybe a additional heatsink like a heatpipe for example will solve this problem??? I will try....
Can anyone explain me this bypassing? Then i can test my m2 by that. And i'm looking for a test to check the dat 1521 and dat 1018 if this piece is ok or not....
sorry for my bad english, mybe anyone can help me greenhorn ;-))
Thanks by now...
I'm a new member. I'm looking for a circuit or schematic plan for the kenwood basic c2 preamp and kenwood basic m2 amp. A few weeks ago i bought a c2 and its sound is very good. Now i'm looking for a m2, but all i've found was defect amps. I suppose the powercircuits dat 1521 and/or dat 1018 have finished there life...
I've red that there is a posibility to bypass the TA2031 and than the amp maybe runs fine ... only that it runs real hot! Maybe a additional heatsink like a heatpipe for example will solve this problem??? I will try....
Can anyone explain me this bypassing? Then i can test my m2 by that. And i'm looking for a test to check the dat 1521 and dat 1018 if this piece is ok or not....
sorry for my bad english, mybe anyone can help me greenhorn ;-))
Thanks by now...
I'm not able to help you but please don't replicate your post if no one seems to answer.
Anyway, thread is back on top now, cross your fingers. 🙂
/Hugo
Anyway, thread is back on top now, cross your fingers. 🙂
/Hugo
i'sorry about that , but i'm a new member and i've a lot to learn abaut this forum.... and to work whith it...
excuse me please ;-))
excuse me please ;-))
solution from other Thread....?
Hi,
i red this bypassing-method in this forum in a thread made by the members SVI2004 and K-amps. But unfortunatly i'm a new member und so i'm under moderation. It's not allowed to me to send e-mails direct to members.... :-(.
So I've to wait.....
Maybe is my question in the wrong category placed?
Hi,
i red this bypassing-method in this forum in a thread made by the members SVI2004 and K-amps. But unfortunatly i'm a new member und so i'm under moderation. It's not allowed to me to send e-mails direct to members.... :-(.
So I've to wait.....
Maybe is my question in the wrong category placed?
You can buy the DAT1521N and DAT1521P devices, along with the Trio Kenwood TA2031 from here Buy Electronic components,Ic,Module,Transistor at UTSOURCE
$5.00AU for the DAT devices and $10.00AU for the TA2031.
As it happens I repaired an M2 recently.
$5.00AU for the DAT devices and $10.00AU for the TA2031.
As it happens I repaired an M2 recently.
Hi,
I have the M2A repair manual.
If you are interested, you can contact me by PM and I'll send you.
I just make a submition for the DAT 1018N/P, DAT 1521N/P and TA2031 for my two M2A, on the site below (Buy Electronic components,Ic,Module,Transistor at UTSOURCE).
The current price is 6$ each component ...
Thanks to Muff for this URL.
I hope this site is serious, but it seems !
I'm also interested in advices to repair a M2A, but there is a very very long time that I did not make any more electronics !
I have the M2A repair manual.
If you are interested, you can contact me by PM and I'll send you.
I just make a submition for the DAT 1018N/P, DAT 1521N/P and TA2031 for my two M2A, on the site below (Buy Electronic components,Ic,Module,Transistor at UTSOURCE).
The current price is 6$ each component ...
Thanks to Muff for this URL.
I hope this site is serious, but it seems !
I'm also interested in advices to repair a M2A, but there is a very very long time that I did not make any more electronics !
- Status
- Not open for further replies.