I am a beginner and i need help with my speaker build

So i will give now the photo and information of the build
For the box of the speaker i have found a guy that gave it to me for free.

As for the speakers I have chosen
Subwoofer : Dayton audio epique E180He-44(does 4+4 mean 8ohm?)

Midrange: Markaudio maop 11

Tweeter : Skar audio VX4-ST super tweeter 4 ohm ( I wanted to buy from kleinanzeigen a scan speak 2905 tweeter but it is sold)

For the amp i chosen Wondom jab5 4×100W
And a battery board that need to be change because it can not supply enought amps to the amp board
And i want to build the crossover myself so i can learn something new and useful
 

Attachments

  • 20241126_181620.JPG
    20241126_181620.JPG
    303.3 KB · Views: 44
  • 20241006_125043.JPG
    20241006_125043.JPG
    377.2 KB · Views: 44
  • 20241006_124925.JPG
    20241006_124925.JPG
    412.8 KB · Views: 44
  • 20241006_124833.JPG
    20241006_124833.JPG
    435.3 KB · Views: 46
  • 20241006_124821.JPG
    20241006_124821.JPG
    411.7 KB · Views: 43
  • 20241006_124714.JPG
    20241006_124714.JPG
    413.4 KB · Views: 39
  • 20241006_124704.JPG
    20241006_124704.JPG
    447.1 KB · Views: 39
  • 20241006_124654.JPG
    20241006_124654.JPG
    486.2 KB · Views: 38
  • 20241006_124624.JPG
    20241006_124624.JPG
    475.1 KB · Views: 34
  • 20241126_180059.JPG
    20241126_180059.JPG
    292.5 KB · Views: 38
  • 20241126_180706.JPG
    20241126_180706.JPG
    530 KB · Views: 38
  • 20241126_180730.JPG
    20241126_180730.JPG
    457.3 KB · Views: 44
  • 20241126_181615.JPG
    20241126_181615.JPG
    306 KB · Views: 46
  • 20241126_181608.JPG
    20241126_181608.JPG
    273.7 KB · Views: 37
  • 20241126_181437.JPG
    20241126_181437.JPG
    280.7 KB · Views: 41
  • 20241126_181336.JPG
    20241126_181336.JPG
    264 KB · Views: 41
  • 20241126_181248.JPG
    20241126_181248.JPG
    273.1 KB · Views: 44
  • 20241126_181220.JPG
    20241126_181220.JPG
    448.3 KB · Views: 44
  • 20241126_181116.JPG
    20241126_181116.JPG
    339.6 KB · Views: 36
  • 20241126_180856.JPG
    20241126_180856.JPG
    298.1 KB · Views: 46
Last edited:
PDF from amp board and battery board
I am open to design changes since I think that I have made a lot of mistakes
 

Attachments

You may try this one! opps... opposite of 1.8mH the cap value is 3.3uF 🙂

note: use all cap min 100V, 2.2/3.3/4.7 are quite reasonable price but 15/33 may be quite a bit expensive but you may use two electrolytic capacitor in serise in this manner ---| (---) |---- [33 + 33 uf = 16.5 uf]
 

Attachments

  • DSC_0332~2.JPG
    DSC_0332~2.JPG
    230.4 KB · Views: 40
Last edited:
Maybe it's better to put the work In the passive filters for the Maop 11 and the Skar tweeter. Since there are 2 amplifiers per channel, the crossover frequency can be kept rather low (200-300 Hz?) ...
I dunno, the dual voice coil suggests to use all the 4 channels for the woofers!!!
You mean that I should connect al the 8 cables to the subwoofer since the amp board can 4 ch 100w , 3 ch 1×200w 2×100w or 2 ch 2×200w
 
I don't know your attitude towards this build. If it needs batteries, then it's gotta be mobile or... private grid!!
So, if mobile and less power hungry, try 2 channels splitted woofer( series connected) and midwoofer+twetter passive crossed.
Or the power subwoofer system that uses 2 more amplifiers for the midwoofer and tweeter.