Dear members,
I'm new, i'm french, i'm 31years old.
Sorry for my bad english....
I'm show you my new DIY d'Apolito loudspeaker:
Specs by Loudspeaker:
2X: HI-VI D5.8
Overview D5.8 Bass-Midrange_HiVi, Inc.
1X: Audax TW025A16
AATV - Sylvain HOULBERT - TW025A16
All components SCR from MHP:
MHP (la Maison du Haut-Parleur) : concepteur français de kits d'enceintes pour la HI-FI et le Home Cinéma...
& Audiophonics:
Audiophonics - Câbles, Amplificateurs et Accessoires DIY
I start the construction ASAP...
Some photos.....
Regards.
The Woofers
The Wood
The Insulating material
My DIY Tool
The Speaker Conectors
The Wire
The Sheathe cotton with Argent Solder
I'm new, i'm french, i'm 31years old.
Sorry for my bad english....
I'm show you my new DIY d'Apolito loudspeaker:
Specs by Loudspeaker:
2X: HI-VI D5.8
Overview D5.8 Bass-Midrange_HiVi, Inc.
1X: Audax TW025A16
AATV - Sylvain HOULBERT - TW025A16
All components SCR from MHP:
MHP (la Maison du Haut-Parleur) : concepteur français de kits d'enceintes pour la HI-FI et le Home Cinéma...
& Audiophonics:
Audiophonics - Câbles, Amplificateurs et Accessoires DIY
I start the construction ASAP...
Some photos.....
Regards.
The Woofers
An externally hosted image should be here but it was not working when we last tested it.
An externally hosted image should be here but it was not working when we last tested it.
The Wood
An externally hosted image should be here but it was not working when we last tested it.
The Insulating material
An externally hosted image should be here but it was not working when we last tested it.
My DIY Tool
An externally hosted image should be here but it was not working when we last tested it.
The Speaker Conectors
An externally hosted image should be here but it was not working when we last tested it.
The Wire
An externally hosted image should be here but it was not working when we last tested it.
The Sheathe cotton with Argent Solder
An externally hosted image should be here but it was not working when we last tested it.
woofer wont crossover high enough
They only go to 1000 hz before dropping off
These would be a better choice and at a descent price wire in parallel and 5 ohm load resistor and then crossed over around 3 khz or preferrably at 3.2 khz
They only go to 1000 hz before dropping off
These would be a better choice and at a descent price wire in parallel and 5 ohm load resistor and then crossed over around 3 khz or preferrably at 3.2 khz
Member
Joined 2003
3200Hz is definitely too high for the D5.8, and not a very good choice for D'apolito speaker either IMO.
D5.8 looks to have not very good frequency response, usable to about 1kHz for a 5.25" driver is not very promising. D6.8 looks much better in comparison.
Can you share any design details? simulated crossover, transfer function, etc? This would be more interesting than photos of coils of wire and piles of wood. 😉
D5.8 looks to have not very good frequency response, usable to about 1kHz for a 5.25" driver is not very promising. D6.8 looks much better in comparison.
Can you share any design details? simulated crossover, transfer function, etc? This would be more interesting than photos of coils of wire and piles of wood. 😉
Here alls the diagrams of my loudspeaker, on the Web-site of D. Petoin.
THank's for him..
Plan automatique d'une enceinte 3/3
THank's for him..
Plan automatique d'une enceinte 3/3
Day 1:
Front of face-plate
Back of face-plate
Front of face-plate
An externally hosted image should be here but it was not working when we last tested it.
An externally hosted image should be here but it was not working when we last tested it.
Back of face-plate
An externally hosted image should be here but it was not working when we last tested it.
Today the last components.
Tweeters:
Components SCR:
The self 0,8mH downgrade to 0,7mH
Tweeters:
An externally hosted image should be here but it was not working when we last tested it.
An externally hosted image should be here but it was not working when we last tested it.
Components SCR:
An externally hosted image should be here but it was not working when we last tested it.
The self 0,8mH downgrade to 0,7mH
Member
Joined 2003
Textbook crossover at 3.2kHz is not going to be good.
I will say again, 3.2kHz is a bit too high for d'apolito, and a lot too high for D5.8
This speaker will make sound, that is all I would expect.
I will say again, 3.2kHz is a bit too high for d'apolito, and a lot too high for D5.8
This speaker will make sound, that is all I would expect.
Day 2:
An externally hosted image should be here but it was not working when we last tested it.
An externally hosted image should be here but it was not working when we last tested it.
An externally hosted image should be here but it was not working when we last tested it.
An externally hosted image should be here but it was not working when we last tested it.
Hello,
The final assembly of cabinets.
The cabinets ready to receive the front face-plate.
The final assembly of cabinets.
The cabinets ready to receive the front face-plate.
An externally hosted image should be here but it was not working when we last tested it.
The crossover part 1, after downgrading the self to the good values. Before assembling of components.
An externally hosted image should be here but it was not working when we last tested it.
Today...
An externally hosted image should be here but it was not working when we last tested it.
An externally hosted image should be here but it was not working when we last tested it.
An externally hosted image should be here but it was not working when we last tested it.
An externally hosted image should be here but it was not working when we last tested it.
- Status
- Not open for further replies.