Cheapest PRINTED CIRCUIT BOARD, on FR4 support
An externally hosted image should be here but it was not working when we last tested it.
Silkcreen of above PCB (painted with soldering flux for protection against scratching)
An externally hosted image should be here but it was not working when we last tested it.
Cheap PCB on FR4 support
An externally hosted image should be here but it was not working when we last tested it.
Cheapest home-made printed circuit boards with semiprofessional look.
An externally hosted image should be here but it was not working when we last tested it.
PCB silkscreen of components
An externally hosted image should be here but it was not working when we last tested it.
I can not understand you ..what you mean that " I couldn't find your advert "
-------------
Isn't look bad ( material is similar with CEM3 ...cheaper than FR4 )
By the way , how much was the cost of your attached board 150x90 mm ?
-------------
Isn't look bad ( material is similar with CEM3 ...cheaper than FR4 )
By the way , how much was the cost of your attached board 150x90 mm ?
Last edited:
My pcb's released for others are also DIY.
For PCB150x90 ( your presented pcb) , the cost is 6 Euro / board , on FR4 ( fiberglass ) .....and 5 Euro on CEM3 ( presented pcb's on this support type in my post - yellow nontransparent support)
DRILLING IS INCLUDED. ( never mind the holes numbers )
As bonus ......also painted with transparent soldering flux and SILKSCREEN also as bonus.
FR4 has better behavior at soldering than other supports, like CEM , XPC ( your pcb )
Good luck to "drilling " .....and maybe ( if you agree ) ,you'll post here your drilled pcb.
All the best,
Mihai
For PCB150x90 ( your presented pcb) , the cost is 6 Euro / board , on FR4 ( fiberglass ) .....and 5 Euro on CEM3 ( presented pcb's on this support type in my post - yellow nontransparent support)
DRILLING IS INCLUDED. ( never mind the holes numbers )
As bonus ......also painted with transparent soldering flux and SILKSCREEN also as bonus.
FR4 has better behavior at soldering than other supports, like CEM , XPC ( your pcb )
Good luck to "drilling " .....and maybe ( if you agree ) ,you'll post here your drilled pcb.
All the best,
Mihai
Last edited:
OK, I'll forgoe the drilling. I'd like to try one of your FR4 boards. Can you make the B9A holes 1.6mm and the OCTAL holes 2.5mm diameter please.
Please let me know how you would like the images, I normally view the boards from the TOP, ie the component side.
Finished size is 150 x 90mm.
I'm not interested in silk screen.
Thank you.
Please let me know how you would like the images, I normally view the boards from the TOP, ie the component side.
Finished size is 150 x 90mm.
I'm not interested in silk screen.
Thank you.
Attachments
Last edited:
Double layer PCB - perfect layers synchronizing ( TOP- BOTTOM )
Below you can find the TOP layer.
Below you can find the TOP layer.
An externally hosted image should be here but it was not working when we last tested it.
Hello
I just sent you an e-mail with details for 4 (four) pcb's that I would like you to make in FR4.
Please let me know if you got it.
Best regards
Ricardo Cruz
I just sent you an e-mail with details for 4 (four) pcb's that I would like you to make in FR4.
Please let me know if you got it.
Best regards
Ricardo Cruz
Cheapest TINNED PCB on FR4 support
An externally hosted image should be here but it was not working when we last tested it.
Tinned PCB ( scanned pcb board )
An externally hosted image should be here but it was not working when we last tested it.
Sorry , I was really very busy with some pcb's in last weekend for some friends of mine.........and I had not time to study your file sent, but I try to answer you , till this Friday evening.
Regards,
Mihai
Regards,
Mihai
FR4 cheapest PCB
An externally hosted image should be here but it was not working when we last tested it.
