It's a Chevy 502 -- fuel injected -- no in my plant, however.
I've matched up a bunch of FQA19N's for my BA1. Monsoon season in NJ has kept me indoors.
I've matched up a bunch of FQA19N's for my BA1. Monsoon season in NJ has kept me indoors.
Eastern Rain out.
No kidding, got a good deal of an F3 put together. Cant get to much yard work together on my week off.
Jack, are you going to offer up a matched set of 6 N channels for BA-1 for the shoppe?
😀
jackinnj said:
No kidding, got a good deal of an F3 put together. Cant get to much yard work together on my week off.
Jack, are you going to offer up a matched set of 6 N channels for BA-1 for the shoppe?
😀
Actual Ba
I know this is somewhat off topic but has there been any word on the actual Burning Amp Festival other than just the date. I just found out i will be in San Francisco that weekwnd and would like to attend
Tom
I know this is somewhat off topic but has there been any word on the actual Burning Amp Festival other than just the date. I just found out i will be in San Francisco that weekwnd and would like to attend
Tom
Not really off topic, but here is the Burning Amp info:
http://www.diyaudio.com/forums/showthread.php?postid=1885181#post1885181
http://www.diyaudio.com/forums/showthread.php?postid=1885181#post1885181
Some progress finally
As I have mentioned, this pcb layout has been delayed by some decision making behind the scenes, but now we are ready to roll! 😀
Here is the layout for BA-1 output section. The bias board is 55x45 mm and the single ended output board is 240x45 mm.
The gain board is the same as BA-2, which can be found here:
http://www.diyaudio.com/forums/pass-labs/150653-burning-amplifier-ba-2-a-11.html#post1989526
As I have mentioned, this pcb layout has been delayed by some decision making behind the scenes, but now we are ready to roll! 😀
Here is the layout for BA-1 output section. The bias board is 55x45 mm and the single ended output board is 240x45 mm.
The gain board is the same as BA-2, which can be found here:
http://www.diyaudio.com/forums/pass-labs/150653-burning-amplifier-ba-2-a-11.html#post1989526
Attachments
Here is some explanation of the various boards:
http://www.diyaudio.com/forums/pass-labs/150653-burning-amplifier-ba-2-a-15.html#post2020813
The Gain board , which is in a fetching mirror image format, works for a BA-1 or BA-2
The BA-1 bias boards and output boards are specific to the BA-1 and are single ended.
When a variation on the Gain board comes out it will work with these bias and output boards, just substitute the new gain stage, and viola-new amp!
Mark
http://www.diyaudio.com/forums/pass-labs/150653-burning-amplifier-ba-2-a-15.html#post2020813
The Gain board , which is in a fetching mirror image format, works for a BA-1 or BA-2
The BA-1 bias boards and output boards are specific to the BA-1 and are single ended.
When a variation on the Gain board comes out it will work with these bias and output boards, just substitute the new gain stage, and viola-new amp!
Mark
CViller, from what I can see, we need two output boards per channel, one for positive rail, one for negative rail. Can you confirm that?
Happy Holidays guys.
Happy Holidays guys.
Between the output stages from BA1 and BA2 can be used a large solid toogle switch. (also on amps outputs) -it would be possible to choose which stage to listen😀
Happy holidays to you!
I am quite sure that only one output board is needed per channel, the devices alternate, but I'm sure cviller will pop up soon and remove all doubt..
Mark
Sure. 😉
Mark is correct! One output board is for one channel. You can mount the output boards in parallel if you want more output devices per channel.
Mark is correct! One output board is for one channel. You can mount the output boards in parallel if you want more output devices per channel.
OK, the BA-1 and BA-2 boards are available at the "Secret" diyAudio store just for you wanting Burning Amps!
http://www.diyaudio.com/secretstore/
The thing to keep in mind is that the boards are "beta" for now because no one has completed an amp.
So there is a slight chance that there will be issues with some aspect of the boards. If so, it should be easy to fix, as the boards are modular so that everything wouldn't have to be replaced if there is some tremendous issue with one of them. If there is a big problem we will replace the defective boards, if it is just a matter of a jumper wire and cutting a trace, or bending leads to insert them, then that won't be considered a serious defect.
If you aren't willing to be a pioneer, we suggest that you wait for the go-ahead once an amp of the model that you want is proven.
On the other hand, we want people to build some, so for the 2 first amps of each type that are reported to work, with posted photo documentation , we will give the member who makes them store credit for the cost of the boards towards any future purchase. So the boards would be pretty much free for those that make the first 2 amps of each type.
Looking forward to the reports. And please post here if there is a problem with the store.
Variac
http://www.diyaudio.com/secretstore/
The thing to keep in mind is that the boards are "beta" for now because no one has completed an amp.
So there is a slight chance that there will be issues with some aspect of the boards. If so, it should be easy to fix, as the boards are modular so that everything wouldn't have to be replaced if there is some tremendous issue with one of them. If there is a big problem we will replace the defective boards, if it is just a matter of a jumper wire and cutting a trace, or bending leads to insert them, then that won't be considered a serious defect.
If you aren't willing to be a pioneer, we suggest that you wait for the go-ahead once an amp of the model that you want is proven.
On the other hand, we want people to build some, so for the 2 first amps of each type that are reported to work, with posted photo documentation , we will give the member who makes them store credit for the cost of the boards towards any future purchase. So the boards would be pretty much free for those that make the first 2 amps of each type.
Looking forward to the reports. And please post here if there is a problem with the store.
Variac
Last edited: