not a shorted turn, it needs to pass around the core and be electrically continuous to be a turn.
It acts as a gauss band.
It acts as a gauss band.
Absolutely a beautiful and clean design!
How did you make the chassis? Were the cut outs punched or make with a water jet?
-David
How did you make the chassis? Were the cut outs punched or make with a water jet?
-David
Two more pics:
The chassis cut outs were punched. Chassis dimensions are 25x25x16 cm and was made here http://www.mali-sp.si/index.php?stran=lang&l=en based on my design. All in all I am satisfied, but the details are less accurate than I wished them to be. Maybe with two or three more phone calls... Mali can make excelent chssis but all depends from $.
GeMa
An externally hosted image should be here but it was not working when we last tested it.
An externally hosted image should be here but it was not working when we last tested it.
The chassis cut outs were punched. Chassis dimensions are 25x25x16 cm and was made here http://www.mali-sp.si/index.php?stran=lang&l=en based on my design. All in all I am satisfied, but the details are less accurate than I wished them to be. Maybe with two or three more phone calls... Mali can make excelent chssis but all depends from $.
GeMa
Gema: Beautiful amplifiers all around...you should be very proud.
I would love it if you could share details on the power supply with schematics if possible.
Details of how you have configured the A30 for mono would also be great.
I am planning to embark on an identical mono A30 (A60?) project.
I would love it if you could share details on the power supply with schematics if possible.
Details of how you have configured the A30 for mono would also be great.
I am planning to embark on an identical mono A30 (A60?) project.
The power supply is basically taken from KRISTIJAN KLJUCARIC web page here http://www.kk-pcb.com/power-3.html My elcos are 10 mF per piece and the value of the coils is somewhat lower because I removed some windings by hand. Where power lines are fitted on the main board I also put elcos and by-passed it. You can find good reading about power supplies for solid state here http://www.tnt-audio.com/clinica/ssps1_e.html
And there is nothing to configure for mono. You just take one channel and put it in a single box…
And there is nothing to configure for mono. You just take one channel and put it in a single box…
This amplifiers beautiful ones, like the Slovene landscape.
To discover the signs of the yellow envy on myself with me.🙂
Gyuri
To discover the signs of the yellow envy on myself with me.🙂
Gyuri
Thank you for the power supply info Gema.
My mistake on the mono question, I had assumed that you bridged the two channels of the A30 to make an A60!
My mistake on the mono question, I had assumed that you bridged the two channels of the A30 to make an A60!
gema said:
Congrats
Wow Truely nice. I wish I could do the same. It's like a commercial run amplifier. keep it comin!
Wow Truely nice. I wish I could do the same. It's like a commercial run amplifier. keep it comin!
hi!
I know its an old thread but can You please repost the adress to power suply schematics?
The one gema gave doesn't work anymore :/
BTW gema
GREAT WORK, I'm really impressed
Excellent job!
How much did it cost to build one?
I know its an old thread but can You please repost the adress to power suply schematics?
The one gema gave doesn't work anymore :/
BTW gema
GREAT WORK, I'm really impressed
Excellent job!How much did it cost to build one?
borutaman said:hi!
I know its an old thread but can You please repost the adress to power suply schematics?
The one gema gave doesn't work anymore :/
BTW gema
GREAT WORK, I'm really impressed
How much did it cost to build one?
The links both work if you remove the "." from the end of the address.
- Status
- Not open for further replies.