I don't want share this H2500, this is dificalt and expensive project for diyers, but if someone can design his own pcb it is posible to build 3 step 2,5kW class-H amp. You can use 2SA1943/2SC5200, but test amp first, before use in PA.
Regards
apexaudio
As would be the maximum voltage without injectors
en español. cuanto seria el voltaje maximo sin los inyectores de voltaje
As would be the maximum voltage without injectors
en español. cuanto seria el voltaje maximo sin los inyectores de voltaje
hi apexaudio
greetings any schematic for diy 3 step supply h class supply
that you might want to share if you dont want to share its ok i repect your
feelings can you tell me if a 3 step supply is used for h 900 wii
1 heating decrease
2 more output power be given out and most of all can such a supply be
used with this amplifier the reason i ask is to learn experiment and how to apply
these 3 step supply for knowledge cant keep on copying have to learn fundamentals so please understand for me your h class power is amazing h900
similiar to qsc isa750
thanking you
andrew lebon
greetings any schematic for diy 3 step supply h class supply
that you might want to share if you dont want to share its ok i repect your
feelings can you tell me if a 3 step supply is used for h 900 wii
1 heating decrease
2 more output power be given out and most of all can such a supply be
used with this amplifier the reason i ask is to learn experiment and how to apply
these 3 step supply for knowledge cant keep on copying have to learn fundamentals so please understand for me your h class power is amazing h900
similiar to qsc isa750
thanking you
andrew lebon
Go to this thread:
http://www.diyaudio.com/forums/solid-state/164208-500w-pa-amplifier-limiter.html
Regards
H900 can be redesign to work in 3 step classs H with more outputs, and you have heating decrease and more power,
Regards
Hi Apex
check schematic from PA amp M10
there is PA Amp with easy linear Class H Stepdriver without IC ...how do you think about this ?
Can I use this linear Class H Stepdriver for quasicomplementary output stage ?
I think it should work because its not switching Rail compare to H900
check schematic from PA amp M10
there is PA Amp with easy linear Class H Stepdriver without IC ...how do you think about this ?
Can I use this linear Class H Stepdriver for quasicomplementary output stage ?
I think it should work because its not switching Rail compare to H900
Last edited:
Your output transistor must be on center of heatsink for maximum heat disipate, maybe you can use only black heatsink, but radiating have wrong position.Hi..Apex, that's my pictures H900 still in progress:
1. Front panel:
2. Rear:
3.
Regards
Thanks Apex...your advice..yes... radiating black heatshink no match with air flow from fan...😕 because this I adding white heatshink...I will try it, if result no satisfaction, I will used only black heatshink...One againt, thanks Apex..
Pozdrav,
Pozdrav,
Apex, I need 900W at 2 ohms instead of 4, which modifications are required? more pairs in output or less voltage in power supply?
thanks
thanks
Hi Apex,
Can you please provide details about the 10uH output coil?
= wire gauge
= no. of turns
= coil diameter
? is it wound around the 4R7 2W resistor ?
? for the zobel network, can we use 10R + 0.1uF ?
Thanks,
Joel
Hi..Apex...my friends ask to me..for PSU H900..Can he used two transformator with seri in secondary tap 57,2v-26,7v-0-0-26,7v-57,2v..0-0 is CT tap.
So, because I no background technic electronica..I hope U will explain to me.
Pozdrav..
So, because I no background technic electronica..I hope U will explain to me.
Pozdrav..