Hey one thing
on cut 7th what are the measurments for the diagonal cut for the brace
also on cut 5th the baffle, what are the measurements for the hole center
on cut 7th what are the measurments for the diagonal cut for the brace
also on cut 5th the baffle, what are the measurements for the hole center
11" on the short side 45 degr angle.
place the woofer as close as posible to the end of the baffle.
make sure it stil fits properly.
aprox 8"center
place the woofer as close as posible to the end of the baffle.
make sure it stil fits properly.
aprox 8"center
where you can get corners like this
the casters and the rubber feet
I want to pimp mine 🙂
well... when i build them 😀
how to make a handle like that
or is better to buy a commercial handle and you made the square hole for it
the casters and the rubber feet
I want to pimp mine 🙂
well... when i build them 😀
how to make a handle like that
or is better to buy a commercial handle and you made the square hole for it
Bjorno
Love it!!!
can you post individual pics full res 🙂... Please Please !!!!😉
hey i see 2 SPL graphs, one is HIFI the other is PA
how do you get the diferent responses, does the plans need to be changed ?
how do you get one or the other
i want it for PA
Last edited:
Hi Maxo,
Why needing individual pictures, why not just hit the zoom/expand cross at the lower left corner of the thumb nail?*
Most of the picture concern the PA version that do not need to be changed, (Epa's cut list is IMO ok, Thanks Epa!) and I only added the Hi-Fi T-TQWT version(enclosed within a wide border line of light Grey color) for comparison, that besides the upper FR boundary differences uses a larger volume = +34L, has a negative tapering that should be properly damped if to achieve Hi-Fi SQ.
*The part of the picture that has the visible lowest resolution is the plot at the lower right corner is depicting:
When trading SPL from the PA variant to BW similar to the T-TQWT's FR:
An +(7-8 dB) shelving function inserted at ~33 Hz(An LT circuit can be used to manipulate the PA variant to achieve a very similar 'low end' like the showed variant 'Hi-Fi' is inherited from another box dimensioning.). Submitting a magnified picture:
b🙂
Attachments
Hey DON , EPA
please tell more about your build
you said people love them
elaborate more , i am excited to build a pair
do i missed somebody that actually built them on this thread ?
chime in if i did
please tell more about your build
you said people love them
elaborate more , i am excited to build a pair
do i missed somebody that actually built them on this thread ?
chime in if i did
hi maxo
i have not bild this one,so can't help you there.
al the numbers are right,and its an easy bild.
i'd say go for it.
see post 24 to 26 and post 36
i have not bild this one,so can't help you there.
al the numbers are right,and its an easy bild.
i'd say go for it.
see post 24 to 26 and post 36
Last edited:
Ok, i almost ready to get the drivers
So they need to be the Eminence Kappa 3015LF
the neodymium or the heavy ones but just the kappa's
or any other than the SS15 from Jbell take right ?
So they need to be the Eminence Kappa 3015LF
the neodymium or the heavy ones but just the kappa's
or any other than the SS15 from Jbell take right ?
Attachments
So that means you have to...DIY...= compare the numbers to epa:s design or my initial design...or to don s. I have no idea what you don't understand...
b🙂
Ic.. well, i think i cant get 3 or 4 drivers of different flavors
so i will stick with the suggested one
so i will stick with the suggested one
dan,
for example cut 1 u got the x dimmension but what is the distance from the top edge od the ply to the horizontal line where u will get a sub panel and a leftover piece for a brace
for example cut 1 u got the x dimmension but what is the distance from the top edge od the ply to the horizontal line where u will get a sub panel and a leftover piece for a brace
what the effff.... i can see now on the cell....but not on the pc... never mind i need to see what the efff with this pc
- Status
- Not open for further replies.