Melbourne Daughterboard for M2X

[jwjarch]

Up to 66 boards X! I think you have a following. 😉

 

[TboneAK]

twitchie (4) boards - Canada
spind (4) boards - Canada
Russellc (4) boards -USA
batty (4) boards - Australia
TungstenAudio (4) boards - USA
zman01 (2) - USA
dBel84 (2) boards - USA
BigE (4) TH boards -Canada
wcwc (2) boards - USA
BRN (2) boards - USA
jwjarch (4) boards - USA
poseidonsvoice (2) boards - USA
tomservo (4) boards - USA
mordikai (4) boards- USA
asanden (4) boards - NL
Vunce (4) boards - USA
vvs07 (4) boards - USA
BEYoung (4) boards - USA
Roundtoit (4) boards - USA
TboneAK (4) boards - USA

 

[xrk971]

Mostly USA - not much action Eurozone?

 

[spind]

twitchie (4) boards - Canada
spind (2) boards - Canada
Russellc (4) boards -USA
batty (4) boards - Australia
TungstenAudio (4) boards - USA
zman01 (2) - USA
dBel84 (2) boards - USA
BigE (4) TH boards -Canada
wcwc (2) boards - USA
BRN (2) boards - USA
jwjarch (4) boards - USA
poseidonsvoice (2) boards - USA
tomservo (4) boards - USA
mordikai (4) boards- USA
asanden (4) boards - NL
Vunce (4) boards - USA
vvs07 (4) boards - USA
BEYoung (4) boards - USA
Roundtoit (4) boards - USA
TboneAK (4) boards - USA


revised my order.
__________________

 

[xrk971]

Sneak Preview of the Melbourne Motherboard by JPS64.

 

[Vunce]

Looks real sweet X!!
If I could make a request for the volume pot pads to accept the larger Alps RK27 in addition to the smaller RK09. Thanks

 

[xrk971]

I think JP can accommodate that - or perhaps you may need to remotely mount the pot and have flying leads from pot to where RK09 is. I generally like my pots panel mounted.

 

[zman01]

X,

Maybe it's due to the pic (I am not sure)- but the volume pot is positioned towards the rear end of the board and looks difficult to reach without a shaft extender... any chance of bringing it a bit forward?

Otherwise layout looks impressive as usual, thanks to JP - we are a bit spoiled. 😀

 

[Vunce]

I think JP can accommodate that - or perhaps you may need to remotely mount the pot......

Kind of like this

 

[xrk971]

Hi Zman01,
JPS64 likes to place the pot symmetrically in the middle of the board so it’s ground pins are on the star ground hub. There are two ground planes left:right and they are split right through the middle of the pot (middle layer between two pot discs). I don’t think he is going to move it closer to the edge as that is not the ideal location from grounding and low noise standpoint - I know, as I have asked before myself 🙂

 

[JPS64]

Hi folks,

ok for ALPS but I‘m not a fan (had in the past big problem with this type) of this type: TKD CP601 (not cheap but my fav) already in parallel.

I‘ll propose something for the guys who like to put pot near to front.

Thinking finishing (with X checking) for end of this week.

JP

 

[Vunce]

Thanks JP, the layout looks fantastic!
Could you add a second set of outputs for subwoofer/bi-amping?

 

[xrk971]

Hi PS64,
You mean this pot for 30 quid?

TKD 2CP-601/S Potentiometer | Hifi Collective

 

[pinnocchio]

Probably closer from your home here:

TKD Potentiomters

Ciao!
Do

 

[meanie]

twitchie (4) boards - Canada
spind (2) boards - Canada
Russellc (4) boards -USA
batty (4) boards - Australia
TungstenAudio (4) boards - USA
zman01 (2) - USA
dBel84 (2) boards - USA
BigE (4) TH boards -Canada
wcwc (2) boards - USA
BRN (2) boards - USA
jwjarch (4) boards - USA
poseidonsvoice (2) boards - USA
tomservo (4) boards - USA
mordikai (4) boards- USA
asanden (4) boards - NL
Vunce (4) boards - USA
vvs07 (4) boards - USA
BEYoung (4) boards - USA
Roundtoit (4) boards - USA
TboneAK (4) boards - USA
Meanie (4) boards - Singapore

 

[xrk971]

Thanks, Do. $40 is not too bad for the ultimate preamp I suppose. Sort of a big change though from my usual $5 RK09 pots. 🙂

 

[BRN]

I have been using the eBay DACT stepped attenuators in my preamps. I think they work well and sound better than a pot. May have to give the TDK a try.

 

[xrk971]

That's TKD, not TDK... as in Tae Kwon Do 🙂

 

[BRN]

Funny. I guess TDK is ingrained into my memory because of all the cassettes I bought from them back in the 80s.

 

[xrk971]

I think it is time to close the first GB for the Melbourne DB's. If your name is on this list, please send me a PM with your PayPal account email, qnty ordered, and country to ship to, and I will send you an invoice. Price as stated earlier is $20/pair and $5 for tracked shipping to US address, $10 to CAN address, and $15 everywhere else.

Thanks,
X

twitchie (4) boards - Canada
spind (2) boards - Canada
Russellc (4) boards -USA
batty (4) boards - Australia
TungstenAudio (4) boards - USA
zman01 (2) - USA
dBel84 (2) boards - USA
BigE (4) TH boards -Canada
wcwc (2) boards - USA
BRN (2) boards - USA
jwjarch (4) boards - USA
poseidonsvoice (2) boards - USA
tomservo (4) boards - USA
mordikai (4) boards- USA
asanden (4) boards - NL
Vunce (4) boards - USA
vvs07 (4) boards - USA
BEYoung (4) boards - USA
Roundtoit (4) boards - USA
TboneAK (4) boards - USA
Meanie (4) boards - Singapore