http://www.npfasteners.com/pdfs/max-rec-tightening-torque.pdf
M4 = ~2 X M3
But tread on sink will give way much earlier even if one uses elicoil inserts
M4 = ~2 X M3
But tread on sink will give way much earlier even if one uses elicoil inserts
Amazon.co.uk: helicoil inserts
M4 = ~2XM3 torque but tread strip off alu sinks before that especialy if one do not use Helicoils inserts
M4 = ~2XM3 torque but tread strip off alu sinks before that especialy if one do not use Helicoils inserts
http://www.diyaudio.com/forums/attachments/pass-labs/261113d1326899846-my-f5-mule-001.jpg
Yup M6 is beterer and M8 even more but then one need Chain block to move Papa amp or ask Zen Mod how painful is back pain
If done properly Kerafol will take the pressure and more pressure = less resistance realistically the limit is when TO case give up and crack
Yup M6 is beterer and M8 even more but then one need Chain block to move Papa amp or ask Zen Mod how painful is back pain
If done properly Kerafol will take the pressure and more pressure = less resistance realistically the limit is when TO case give up and crack
Downloads / Data sheets
From data sheet for 82/86 see on picture what up when pressure is 40 N/ cm square
Nah no idea about conversion from pints to liters
From data sheet for 82/86 see on picture what up when pressure is 40 N/ cm square
Nah no idea about conversion from pints to liters
1/4si is ~1.6 cm2
Advisable torque for a TO-220 is 0.5 Nm (both for a regular one, as for the F-version)
For convenience sake, assume an M3 screw has an effective diameter of 3 mm
T = C * D * F
0.5 = 0.34 * 0.003 * F
F = 490 N
Makes the mounting pressure 306 N/cm2 (>5 times 60 N/cm2)
If the screw is lubricated for the torquing, C is ~0.20 (the C factor also depends on the material), in which case pressure would go up by 70%
(screw bonus is sucker in domus)
For TO-220s, it makes sense to use clamps instead of the mounting hole because of the hole location and top of the package.
Advisable torque for a TO-220 is 0.5 Nm (both for a regular one, as for the F-version)
For convenience sake, assume an M3 screw has an effective diameter of 3 mm
T = C * D * F
0.5 = 0.34 * 0.003 * F
F = 490 N
Makes the mounting pressure 306 N/cm2 (>5 times 60 N/cm2)
If the screw is lubricated for the torquing, C is ~0.20 (the C factor also depends on the material), in which case pressure would go up by 70%
(screw bonus is sucker in domus)
For TO-220s, it makes sense to use clamps instead of the mounting hole because of the hole location and top of the package.
Last edited:
Keratherm 86/525 good enough
Short answer is that 0.5 mm sheet of 86/525 equals 86/82 if compressed to ~0.21 mm thickness.
(5.5 : 6.5 = 0.21 : 0.25)
If you dare to compress it to 0.1 mm, thermal resistance should be twice as good as 86/82.
Costs a fifth more though.
Why bother for 1C difference, read EUVL's article for Linear Audio.
(the older 86/525 datasheet only went to 1 mm sheet thickness, not 0.5 mm)
Short answer is that 0.5 mm sheet of 86/525 equals 86/82 if compressed to ~0.21 mm thickness.
(5.5 : 6.5 = 0.21 : 0.25)
If you dare to compress it to 0.1 mm, thermal resistance should be twice as good as 86/82.
Costs a fifth more though.
Why bother for 1C difference, read EUVL's article for Linear Audio.
(the older 86/525 datasheet only went to 1 mm sheet thickness, not 0.5 mm)
That is reasoning without any non-linearity factor in the ratio between thickness/thermal conductivity applied by the torque. Sure the more torque, the less thickness and better the thermal conductivity. But as it gets thinner, it won't necessarily increase conductivity by a linear factor. There is a limit in compression of these thermal sheets, where thermal conduction can't be raised by any factor.
Still a very good product. ZhouFang used to sell some in his thread.
Best,
nAr
That is reasoning without any non-linearity factor in the ratio between thickness/thermal conductivity applied by the torque.
See the 86/525 graph, mm-K/W is rather linear
(it's pressure-thickness that is not linear)
web site
Yeah, that's odd, Conrad.fr charges €8 more for the same 86/82 sheet size (€36 versus €28 in D/NL)
On the other hand, a 120 x200 mm sheet of 86/525 is €0.99 cheaper in France.
ESP - Heatsink design and transistor mounting
Pretty understandable + links at end are good but Kerafol does not exist at that time
Pretty understandable + links at end are good but Kerafol does not exist at that time
- Home
- Amplifiers
- Pass Labs
- F5 power amplifier