Go Back   Home > Forums > > >
Home Forums Rules Articles diyAudio Store Blogs Gallery Wiki Register Donations FAQ Calendar Search Today's Posts Mark Forums Read

miniDSP Low cost, modular Digital Signal Processor (DSP) kits for the DIYer from miniDSP.

Thread Tools Search this Thread
Old 21st February 2020, 07:26 AM   #1
Ugg10 is offline Ugg10  United Kingdom
diyAudio Member
Join Date: Nov 2017
Location: UK
Default Nanodigi source selection on remote

I've done a search which seems to suggest that this has been sorted but I can't use the official remote to select sources even after "learning" it (both sources learned to the source button).

It switches ok between SPDIF and Toslink from the software and all other buttons work. Also I understand it will only work when not connected to the PC so have checked that even powering the Nanodigi on/off in between.

Software version is v2.3
Firmware version is v2.11
All kit new out of box.

Any pointers to fix this would be gratefully received.
  Reply With Quote
Old 5th March 2020, 03:32 PM   #2
Ugg10 is offline Ugg10  United Kingdom
diyAudio Member
Join Date: Nov 2017
Location: UK
Update - from Minidsp support -

1st response was to reset all of the learned codes in the Minidsp programme. All you do is go through the learning process but don't push the remote button, this will time out and reset the codes to default.

However, this did not fix the issue.

2nd response confirmed that the Nanodigi does not support the toggle function for the two inputs and you have to assign two different buttons to SPDIF and TOSLINK (source and centre arrow button maybe).

Will try this later and if that does not fix it I will see if I have an old RC6 compliant remote to try learning that. Will update if I get a fix.
  Reply With Quote
Old 10th March 2020, 10:12 AM   #3
Ugg10 is offline Ugg10  United Kingdom
diyAudio Member
Join Date: Nov 2017
Location: UK
Update #2

Found an old DVD remote that I had lying around. Programmed this with different buttons for optical and coax spdif (plus other commands), now all works fine.

thought it was worth keeping this info going just in case there are others in the future having the same issue or helps them not buy the minidsp remote and can buy a generic RC6 one.

For info the one I used was a Toshiba SE-R0049 for an SD230E DVD player.

Last edited by Ugg10; 10th March 2020 at 10:20 AM.
  Reply With Quote


Nanodigi source selection on remoteHide this!Advertise here!
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Passive Preamp: Arduino based, remote control, Relay R2R, input selection maxw Analog Line Level 104 18th July 2019 09:13 AM
Source Selection Question SRMcGee Analog Line Level 3 17th January 2018 12:06 PM
Balanced inputs selection board with remote volume control 00940 Analog Line Level 11 31st October 2017 05:46 AM
Source Selection IC danward79 Parts 28 25th November 2008 12:13 AM
GP: Alps remote control VR and/or i/p selection jrsun Group Buys 6 18th May 2006 06:34 AM

New To Site? Need Help?

All times are GMT. The time now is 12:49 PM.

Search Engine Optimisation provided by DragonByte SEO (Pro) - vBulletin Mods & Addons Copyright © 2020 DragonByte Technologies Ltd.
Resources saved on this page: MySQL 15.79%
vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2020 DragonByte Technologies Ltd.
Copyright ©1999-2020 diyAudio