Hypex DLCP no analog audio output (help needed)

bourbon-neat · 10th January 2016, 07:29 PM

Problem: I am not getting any output on the analog outputs.

Steps taken:
I've updated the firmware to v2.1. I've created a basic configuration with unity filters in each biquad position and downloaded my filter configuration to the DLCP. I've tried analog, USB, S/PDIF and Optical inputs. The DLCP seems to boot and operate correctly. The control board recognizes the DLCP. The Filter Designer v4 connects to the DLCP.

Configuration:
DLCP with v2.1 firmware
DLCP Input Board
DLCP Controller board
SMPS DLCP Power Supply
Filter Designer 4 (beta)

bourbon-neat · 13th January 2016, 01:22 AM

I've added pictures showing the DLCP and it LEDs, the cable connections between the PS-DLCP-Input board and the Filter Designer version. I've reflashed the firmware and created a new config file. Still no audio output. Also, I have tried different sources.

Any trouble shooting suggestions will be greatly appreciated.

Thanks,

Jim

NCP · 18th February 2017, 09:35 PM

Hi James. I'm seeing that you have the DLCP connected to the host computer and communicating correctly, with firmware updated all the way to V2.3 right? In that case open the control panel in the software where you tell the DLCP which input to use... that control panel. You will see a control for input level, mute and a window displaying the input level value. There is a bug- at least for me- where everything flips out if you slide the slider but if you directly enter the value in the input level window it works. By default it is at -96. Enter 0 there for unity gain and you should now have output.

10th January 2016, 07:29 PM	#1
bourbon-neat diyAudio Member Join Date: Jan 2010 Location: San Jose, CA	Hypex DLCP no analog audio output (help needed) Problem: I am not getting any output on the analog outputs. Steps taken: I've updated the firmware to v2.1. I've created a basic configuration with unity filters in each biquad position and downloaded my filter configuration to the DLCP. I've tried analog, USB, S/PDIF and Optical inputs. The DLCP seems to boot and operate correctly. The control board recognizes the DLCP. The Filter Designer v4 connects to the DLCP. Configuration: DLCP with v2.1 firmware DLCP Input Board DLCP Controller board SMPS DLCP Power Supply Filter Designer 4 (beta)

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Hypex DLCP - standby mode	georgeus	Digital Line Level	1	25th February 2019 09:13 PM
Hypex NC1200, DLCP, Ian FIFO, WaveIO, Neotech wire, Xhadow+Mundorf con, Lundahl choke	edbk	Swap Meet	30	24th June 2015 12:40 PM
FS: Sitronik Amps, Hypex DLCP, Thel Power Supplys	Guitarfreak	Swap Meet	5	12th February 2015 01:53 AM
FS: Hypex DLCP and input board	mcai7et2	Swap Meet	1	5th November 2013 05:11 PM
installing an analog audio output jack on a television?	peace brainerd	Analog Line Level	7	8th January 2012 06:38 PM

New To Site?	Need Help?
Register to Participate Privacy Statement Contact Us	Frequently Asked Questions Did you forget your password? Mark Forums Read


	Please consider donating to help us continue to serve you. Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving

18th February 2017, 09:35 PM	#3
NCP diyAudio Member Join Date: Aug 2013	Hi James. I'm seeing that you have the DLCP connected to the host computer and communicating correctly, with firmware updated all the way to V2.3 right? In that case open the control panel in the software where you tell the DLCP which input to use... that control panel. You will see a control for input level, mute and a window displaying the input level value. There is a bug- at least for me- where everything flips out if you slide the slider but if you directly enter the value in the input level window it works. By default it is at -96. Enter 0 there for unity gain and you should now have output.