[WTB] Aleph Class A power amp PCB

[vision]

I am looking for Aleph Class A power amp PCB.

MiniAleph or other Aleph PCBs, populated or bare, I'll take them.

Let me know if you have these.

Jason

 

[Stuart Easson]

I think I have some of both...

...I'll take a look this evening, let you know tonight or tomorrow morning...

Stuart

 

[d to the g]

I'd be interested in whatever the OP isn't interested in.

 

[Zen Mod]

after all other (frankly - cheaper) variants , Babelfish is still there .

http://tiny.pl/f526

 

[Stuart Easson]

I have some of these:

I don't want to make any money, so they would cost what I paid plus shipping. Unfortunately I'm not sure what they cost me, if anyone remembers or if I cn figure it out from postings on the board I'll let you know. Other than that make me an offer.

I have a few, perhaps 6 and a couple more with one or more components mounted, how many do you each want?

HTH

Stuart

 

[d to the g]

Stuart,

I'm not familiar as to what thread this board was part of.

I know that the mini-A + expansion boards are $9 for the pair, and I was actually going to just build a mini-A but a full aleph sounds tempting.

Doug

 

[Stuart Easson]

Finally...

...I emailed BrianGT.

Neither of us is sure, but I remembered $20 a pair, he thinks $9 each, it's close enough.

$18 a pair plus cost of shipping via whatever method you'd like.

I should add that I think I have an output board for each aleph board. it is set up for 6 devices but can be split for 2 x 3.

Stuart

 

[d to the g]

Stuart,

A local gentlemen has informed me that he has boards that he is willing to part with, for simplicity it's just easier to arrange locally.

Thanks though!

 

[Stuart Easson]

No problem

Have fun with your build.

Stuart

 

[sandyhooker]

Re: Finally...

...I emailed BrianGT.

Neither of us is sure, but I remembered $20 a pair, he thinks $9 each, it's close enough.

$18 a pair plus cost of shipping via whatever method you'd like.

I should add that I think I have an output board for each aleph board. it is set up for 6 devices but can be split for 2 x 3.

Stuart

I'm ready for a pair ...do you do paypal?? If not let me know how to get the money to you..

 

[Stuart Easson]

Sandy

I'm very happy to do paypal, but let me get back to you once I get home.

I am confident I can sell you pair, but another member bought some of these and I need to check to make sure of what I have.

I think it likely the pair remaining have some mounted components, the boards are single sided, so if you didn't want the previously mounted components I can easily remove them or you could do it yourself.

I can also let you know what they are, take pictures etc, then you can choose appropriately.

Stuart

 

[sandyhooker]

Re: Sandy

I'm very happy to do paypal, but let me get back to you once I get home.

I am confident I can sell you pair, but another member bought some of these and I need to check to make sure of what I have.

I think it likely the pair remaining have some mounted components, the boards are single sided, so if you didn't want the previously mounted components I can easily remove them or you could do it yourself.

I can also let you know what they are, take pictures etc, then you can choose appropriately.

Stuart

Either way ...Ready to go..Pictures arent necessary.

JT

 

[winslow]

I have a set of blue BrianGT amp boards that have a few resistors, 2 caps, and a couple of the terminal blocks installed.

I also have a BrianGT PS board that is populated with 4 22000uf caps, 2 2.7mH 14ga Solen coils, and 2 3.3uf Sonicaps...set up CLC according to Kristen's PS. Everything is soldered using Cardas solder and the only thing not soldered is the LED (which I have). It is ready to use...never been used.

To round it out, I have a 300VA 18-0-18 Antek transformer as well. Never been used.

Perfect for a pair of mini-As or a F4.

If anyone is interested, please email me.

 

[sandyhooker]

Stuart ..Please check your Email .. please confirm your Paypal address

thanks

JTP