Hi DaveM-
Any chance you have a pulley left over, for a welshman ?
If so, what is the cost for your efforts ?
Best,
-Andy-
Any chance you have a pulley left over, for a welshman ?
If so, what is the cost for your efforts ?
Best,
-Andy-
DaveM, sorry, I ignored my own advice
I should have taken it, and reread the last few pages of the thread, since this has become too complicated for me to remember the details. On review, I now see that (post 496) you asked for me to e-mail you shipping info, and I in fact did so (post 501). But I haven't had a response telling me what I owe you and how to pay.
So I'll just shut up now and wait patiently.
Aengus
I should have taken it, and reread the last few pages of the thread, since this has become too complicated for me to remember the details. On review, I now see that (post 496) you asked for me to e-mail you shipping info, and I in fact did so (post 501). But I haven't had a response telling me what I owe you and how to pay.
So I'll just shut up now and wait patiently.
Aengus
pulley
hey Dave,
I have never received any info about paying for the 4 pulleys that I was marked down for. What do I need to do to make sure that I get mine. Thanks!!
-Chris (cwise)
hey Dave,
I have never received any info about paying for the 4 pulleys that I was marked down for. What do I need to do to make sure that I get mine. Thanks!!
-Chris (cwise)
Aengus, Cwise,
Don't worry about it. I have not finished invoicing. The last time I stayed at work until around 9 pm to get done what I have. I believe that there are 3 or 4 people whom I haven't invoiced yet. Don't freak. I just have limited time to work on this. In the words of Charlie Papazian. Relax, have a homebrew, this is supposed to be fun.
NjoyTHEMUSIC,
Let me finish with packaging and shipping what I already have commited to and I will see if there are any left. I believe I may have one or two extra, but don't quote me on that. I will post the results at the end.
I am trying to double check the shaft fit with my motor before they are shipped. So, if there are any left it will definately be the loosest of the pulleys, but with a bit of lock-tite and or some set screws that is surmountable.
DaveM
Don't worry about it. I have not finished invoicing. The last time I stayed at work until around 9 pm to get done what I have. I believe that there are 3 or 4 people whom I haven't invoiced yet. Don't freak. I just have limited time to work on this. In the words of Charlie Papazian. Relax, have a homebrew, this is supposed to be fun.
NjoyTHEMUSIC,
Let me finish with packaging and shipping what I already have commited to and I will see if there are any left. I believe I may have one or two extra, but don't quote me on that. I will post the results at the end.
I am trying to double check the shaft fit with my motor before they are shipped. So, if there are any left it will definately be the loosest of the pulleys, but with a bit of lock-tite and or some set screws that is surmountable.
DaveM
Ah, I always appreciate it when my patience is rewarded without undue periods of waiting 😀
Thanks, Dave: just wanted to be sure that you weren't wondering where my $$ were.
And, BTW: thanks for doing this, and for letting me in late.
Regards.
Aengus
Thanks, Dave: just wanted to be sure that you weren't wondering where my $$ were.
And, BTW: thanks for doing this, and for letting me in late.
Regards.
Aengus
Pulley
Hi Dave.
I'm just confirming that I wanted one pulley that was offered to me (and Aengus) by markgall in post #493. I sent you an email with my shipping info. I have yet to send payment. If markgall did not pay you, as he said, then I'm happy to send payment ASAP. Just drop me a email where I should send payment. Thanks.
cygnus x1
Hi Dave.
I'm just confirming that I wanted one pulley that was offered to me (and Aengus) by markgall in post #493. I sent you an email with my shipping info. I have yet to send payment. If markgall did not pay you, as he said, then I'm happy to send payment ASAP. Just drop me a email where I should send payment. Thanks.
cygnus x1
Hi Dave,
I had sent you a pm about changing my invoice to 1 pulley and letting the other fella's have the other two pulleys but as your pc died you probably didn't get the pm. Let me know what I owe you for the one pulley and I will send the funds with paypal.
Mark
I had sent you a pm about changing my invoice to 1 pulley and letting the other fella's have the other two pulleys but as your pc died you probably didn't get the pm. Let me know what I owe you for the one pulley and I will send the funds with paypal.
Mark
Re: Maxon motor GP...
Stan,
I requested a motor on 10/4 in post #462. I hope I haven't missed the boat!
- Eric
sklimek said:
Stan,
I requested a motor on 10/4 in post #462. I hope I haven't missed the boat!
- Eric
DaveM said:
Dave,
I haven't seen a paypal invoice yet, and I don't know if I've sent you my contact info, it's been so long since I first found out about this thread.... Can you confirm that there's still a pulley for me?
Thanks,
- Eric
O.K., back and found a box from Maxon waiting for us…I’ll try and get these out on Monday.
Eric Weitzman and NjoyTHEMUSIC, I’m sorry that I couldn’t get to you guys, This GB went down very fast because I had very little time to work w/ it, in Fact Pamela did most of the work. Basically when we had the email confirmations from my last 3 posts and as soon as the moolah came in Pamela secured them, I just haven’t been around, on the road this time for 3 weeks due to work
You may want to contact Chuck Fogleman at Maxon Motors do see what he can work out, he responds best by email.
http://www.diyaudio.com/forums/showthread.php?postid=1019471#post1019471
Best - Stan
Eric Weitzman and NjoyTHEMUSIC, I’m sorry that I couldn’t get to you guys, This GB went down very fast because I had very little time to work w/ it, in Fact Pamela did most of the work. Basically when we had the email confirmations from my last 3 posts and as soon as the moolah came in Pamela secured them, I just haven’t been around, on the road this time for 3 weeks due to work
You may want to contact Chuck Fogleman at Maxon Motors do see what he can work out, he responds best by email.
http://www.diyaudio.com/forums/showthread.php?postid=1019471#post1019471
Best - Stan
Attachments
Thanks for trying, Stan. These things happen.
It's difficult to order from Maxon directly because they have a minimum order amount of $250 (in the US anyways, a couple of years ago when I last inquired). That's why the pricing looks so weird in small quantities: 1@250, 2@125, 3@83, ...
- Eric
It's difficult to order from Maxon directly because they have a minimum order amount of $250 (in the US anyways, a couple of years ago when I last inquired). That's why the pricing looks so weird in small quantities: 1@250, 2@125, 3@83, ...
- Eric
Eric Weitzman said:
Hi Eric, I'm thinkin' maybe you and EnjoyTHEMUSIC and maybe one other should get you to the 90 dollar range. Chuck is a bit difficult but I believe you could wrestle three out of him if you smooze him a bit. Also, I bet if you posted that you missed out on this GB its probably pretty good that eventually you will get to 3+ or maybe more in time???
Once again sorry,
Stan
edit: Here is a hint from Bas -
http://www.diyaudio.com/forums/showthread.php?postid=1022308#post1022308😉
Hi sklimek -
Thanks for your consideration ...
I was conversing with your better half - and realised the motor you were ordering was close to one I already had (!) ie- Amax 110179-P06
So, I bailed out of the group buy.
Just so all the others know where they stand regarding getting onto the 'group buy' bandwagon I won't be requiring the motors you ordered - sorry !
All the very best,
-Andy-
Thanks for your consideration ...
I was conversing with your better half - and realised the motor you were ordering was close to one I already had (!) ie- Amax 110179-P06
So, I bailed out of the group buy.
Just so all the others know where they stand regarding getting onto the 'group buy' bandwagon I won't be requiring the motors you ordered - sorry !
All the very best,
-Andy-
GB...
Motors went out today, I have confirmation numbers for all.
1 - Canada
1 - Berlin
1 - Compton, Ca
1 - Caledonia, MI
1 - NYC
Groovey...
Motors went out today, I have confirmation numbers for all.
1 - Canada
1 - Berlin
1 - Compton, Ca
1 - Caledonia, MI
1 - NYC
Groovey...
Hi Stan
I got the USPS confirmation notice in my e-mail. I'm looking forward to actually seeing the motor...which will then, of course, sit on my desk for a long time while I think about the rest of the TT design 🙁
I got the USPS confirmation notice in my e-mail. I'm looking forward to actually seeing the motor...which will then, of course, sit on my desk for a long time while I think about the rest of the TT design 🙁
Any news on when the pulleys are going to be sent out? I've paid a few weeks ago, but I guess DaveM is busy with his house?
What is the status of the pulleys in general ? I have tried to contact DaveM directly but received no answer - I have not received a Paypal invoice nor have I received any other feedback ... :-(
Regards,
Andreas
Regards,
Andreas
AAAaaarrrgghhhhh!!
I'm so sorry. Life has taken over. The pulleys are half packed and waiting for labels and a trip to the post office. I was shooting to get time to finish up this weekend. Somewhere between house, last minute business trip, dead computer and parents visiting progress came to an a$$ screaching halt. I am sorry. I have been hearing the voices in my head saying "what happened, I paid and now I still don't have my pulley." I guess my life is just not set up for running group buys. Not the first to realize this and i'm sure not the last.
I will pack what I can this weekend and ship those.
Sorry to drag this out for you all patiently waiting.
DaveM
I'm so sorry. Life has taken over. The pulleys are half packed and waiting for labels and a trip to the post office. I was shooting to get time to finish up this weekend. Somewhere between house, last minute business trip, dead computer and parents visiting progress came to an a$$ screaching halt. I am sorry. I have been hearing the voices in my head saying "what happened, I paid and now I still don't have my pulley." I guess my life is just not set up for running group buys. Not the first to realize this and i'm sure not the last.
I will pack what I can this weekend and ship those.
Sorry to drag this out for you all patiently waiting.
DaveM
- Status
- Not open for further replies.