Anyone know who sells knobs for rotary switchs and pots? I kinda like the big white plastic ones on Acurus and Mark Levinson stuff. And also those soft rubber ones on the old Carver stuff. But most places just sell little wimpy <1" generic knobs. I'd like something in the 2" range that has some solidity.
Even something flimsy like the volume knobs on most recievers might work.
And by me looking I mean Mouser, Digikey, PartsExpress. I have never looked at Farnell or whatever, but I mean to.
Even something flimsy like the volume knobs on most recievers might work.
And by me looking I mean Mouser, Digikey, PartsExpress. I have never looked at Farnell or whatever, but I mean to.
Yo hybrid! Howdy neighbor, lufkin tx. here.Nuuk (one of those english types hehehe) came up with a great way to make wooden knobs, and they look cool. Ya might try his site as its full of good info.
ron
ron
You may have to scavenge old/surplus/dead equipment for them. Take a day and drive around to all the thrift shops and surplus stores and electronics repair shops and see if anything catches your eye.
A quick search on Google...
http://www.oscarcontrols.com/index_knobs.htm
http://www.surplussales.com/ShaftHardware/Knobs-5.html
http://www.megastar.com/linecard/knobs/shell2.htm
🙂ensen
http://www.oscarcontrols.com/index_knobs.htm
http://www.surplussales.com/ShaftHardware/Knobs-5.html
http://www.megastar.com/linecard/knobs/shell2.htm
🙂ensen
Now, where's the fun in that? 😉
Actually, that doesn't make things any easier as you will have to get the hole for the spindle dead centre and amke sure that the dowel is cut at a perfect right-angle.
I know because a friend turned up some round sections on his lathe for me but I actually found it easier to make the knobs from square section.
There's nothing like speaking from experience! 😎
Try this .... http://www.apexjr.com/knobs.htm
I got some. They look almost exactly like the one that Aragon pre-amp uses.
I got some. They look almost exactly like the one that Aragon pre-amp uses.
Don't let them Harman Specialty guys hear that...
The Levinson knobs are glass pearl blasted and anodized massive Aluminum.
Im guessing the whit ones over at apex jr. are the ones described as;
Aluminim Knob (Round) 1 3/8" dia 3/4" tall 1/4" hole w/set screw $4.50ea
Those are like perfectly exactlt what i was looking for....plus i have heard of apex jr.!
Oh I see there on the new page, thats why I havent seem them their before
Aluminim Knob (Round) 1 3/8" dia 3/4" tall 1/4" hole w/set screw $4.50ea
Those are like perfectly exactlt what i was looking for....plus i have heard of apex jr.!
Oh I see there on the new page, thats why I havent seem them their before
You might also check out some of the aftermarket guitar knobs out there. They're usually not very large, but they do come in a wide variety of shapes and colors. Shaft size may not be right, though.
Ton's o' guitar knobs here.
The ones which have set screws will fit your 1/4" pot shafts:
http://www.greggrogersguitars.com/knobs_new.html
The ones which have set screws will fit your 1/4" pot shafts:
http://www.greggrogersguitars.com/knobs_new.html
Your guitar knob link shows a couple of skull knob. It would really look funky if someone uses the skull knob on their pre-amp.
Arcade game controls are big, rugged and designed for pots and encoders.
http://retroblast.com/reviews/roundup6.html
🙂ensen.
http://retroblast.com/reviews/roundup6.html
🙂ensen.
Bricolo the knobs are Alcoa 6061 billet and only polished. No chrome or coating on the finished product.
Here is the latest in knobs for pots. These are low noise knobs at http://www.referenceaudiomods.com/M...OB_C37_C&Category_Code=VOLUME&Product_Count=2 .
Regards,
Ray
Regards,
Ray
- Status
- Not open for further replies.