Thanks for kind comments guys.
ratbagp: That is a good point about the slight hum on the right. I'll leave it alone for a while at least because you can't detect any hum over 1m from the speaker. I'm amazed how quiet this amp is actually. Other ones that I've built have always needed the earth scheme sorting. Not this one.
pinnocchio: To get some air flowing round the heat sinks I have raised them up above the base of the cabinet using metal standoffs. You can't tell from the photos. Not ideal but should help a bit. The heat sinks touch the front and back panels of the case which also helps.
ratbagp: That is a good point about the slight hum on the right. I'll leave it alone for a while at least because you can't detect any hum over 1m from the speaker. I'm amazed how quiet this amp is actually. Other ones that I've built have always needed the earth scheme sorting. Not this one.
pinnocchio: To get some air flowing round the heat sinks I have raised them up above the base of the cabinet using metal standoffs. You can't tell from the photos. Not ideal but should help a bit. The heat sinks touch the front and back panels of the case which also helps.
Nice job. Regarding right channel buzz I would suggest to move your power connector to the middle section of your enclosure closer to transformers.
George
George
Thanks George. There was already a hole cut in the panel when I bought it. I think a metal cover is the best solution.
How much to UK?
Hi all,
Just spotted this thread and my interested had been sparked.
Could you give me some idea of cost to get a set of these PCB's to the UK please?
Many thanks
Roy.
Hi all,
Just spotted this thread and my interested had been sparked.
Could you give me some idea of cost to get a set of these PCB's to the UK please?
Many thanks
Roy.
Roy,
I'm considering a third group buy at this late stage; 172 of these boards have been sold already at a price of $AUD68 a pair, including small semis and shipping.
However, I have 11 on order right now (or is it 13?) so I'm nearing the end. I would say I will close it off at 20, since beyond that I will need to do another 100 and I'm not confident I can sell another 100.
Cheers,
Hugh
I'm considering a third group buy at this late stage; 172 of these boards have been sold already at a price of $AUD68 a pair, including small semis and shipping.
However, I have 11 on order right now (or is it 13?) so I'm nearing the end. I would say I will close it off at 20, since beyond that I will need to do another 100 and I'm not confident I can sell another 100.
Cheers,
Hugh
hey i'll take 2 more sets if you do another hehe 🙂 going biamp and just ordered the heatsinks and trannies for the first set of boards i built .
yes i'm a hoarder/collecter . short money for boards for a great amp .
as i said before , if this amp was more widely known as in outside of aksa's board , it would be a going sell out . not sure of forum rules to advert in groupbuy or other forums .
cheers Woody
yes i'm a hoarder/collecter . short money for boards for a great amp .
as i said before , if this amp was more widely known as in outside of aksa's board , it would be a going sell out . not sure of forum rules to advert in groupbuy or other forums .
cheers Woody
Hi Hugh,
So far we have the following people
hoxuanduc=2
pinnocchio=3
bbe=2
koldby=4
chalkandtalk=2
Woody1911a1=4
Total = 17
Looks like we're almost at the 20 mark!
3 more boards guys and gals
So far we have the following people
hoxuanduc=2
pinnocchio=3
bbe=2
koldby=4
chalkandtalk=2
Woody1911a1=4
Total = 17
Looks like we're almost at the 20 mark!
3 more boards guys and gals
We're now at 19 boards!!!
One more
hoxuanduc=2
pinnocchio=3
bbe=2
koldby=4
chalkandtalk=2
Woody1911a1=4
lloop9=2
Total = 19
Yessss.... getting closer!
One more
hoxuanduc=2
pinnocchio=3
bbe=2
koldby=4
chalkandtalk=2
Woody1911a1=4
lloop9=2
Total = 19
Yessss.... getting closer!
ULP........ THIRD Group Buy now FILLED!!
That's it, guys, third group buy filled, I hope that my semis hold out......
I will examine my stock this weekend.
Many thanks,
Hugh
That's it, guys, third group buy filled, I hope that my semis hold out......
I will examine my stock this weekend.
Many thanks,
Hugh
Speakers protection
Hi Hugh,
Do we need to have any speaker protection circuit with this amplifier?
Thanks,
Igor
Hi Hugh,
Do we need to have any speaker protection circuit with this amplifier?
Thanks,
Igor
STOP!! NO MORE ORDERS PLEASE!!
Igor,
The only speaker protection I would use would be DC sense, so that any DC voltage more than +/-2V or so automatically disconnects the speaker.
This is a separate circuit, however, and it mandates use of a relay, which many say degrades the sound quality.
That, I've found, does depend on the relay. The Amplimo product is designed for it and sounds good, I'm told.
Omron make one specifically for this task, but it's hard to find.
I do not use speaker protection on small amps and have never had problems, but, of course, YMMV.
Cheers,
Hugh
Igor,
The only speaker protection I would use would be DC sense, so that any DC voltage more than +/-2V or so automatically disconnects the speaker.
This is a separate circuit, however, and it mandates use of a relay, which many say degrades the sound quality.
That, I've found, does depend on the relay. The Amplimo product is designed for it and sounds good, I'm told.
Omron make one specifically for this task, but it's hard to find.
I do not use speaker protection on small amps and have never had problems, but, of course, YMMV.
Cheers,
Hugh
Hi Hugh
I was thinking that 20pcs is minimum to start GB#3! .... I just see that GB#3 is filled?
Hope that 2 boards more is not a problem.
best regards
tome
I was thinking that 20pcs is minimum to start GB#3! .... I just see that GB#3 is filled?
Hope that 2 boards more is not a problem.
best regards
tome
Hi team - I was lucky enough to stumble across this thread in time to snaffle a couple of boards - have boards/parts/case just need the time and motivation. It strikes me that with so many boards out already that there should be more comments on the sound/performance of this amp. The ones I've seen look promising so I can't wait. I was lucky enough to trial a Naksa 100 amp last week, that was fun. Roll on Fetzilla !
I finally was able to finish and power up one of the FetZilla and finished the second one but not powered yet...
With only one of them working I can't tell lots on the sound but I love what I'm hearing so far.
Will do a full write up once I have 50+ hours of burn in time.
Hugh, did you go through your semis?
Ciao!
Do
With only one of them working I can't tell lots on the sound but I love what I'm hearing so far.
Will do a full write up once I have 50+ hours of burn in time.
Hugh, did you go through your semis?
Ciao!
Do
- Status
- Not open for further replies.