P Perry Babin Member Joined 2003 bcae1.com 2012-12-02 10:26 am #21 2012-12-02 10:26 am #21 Lower would be better to see if that the only problem. You can use a leaded resistor if you have one of the correct value. seankane Member Joined 2010 2012-12-02 10:29 am #22 2012-12-02 10:29 am #22 How about a .1 ohm source resistor for a rockford amp? P Perry Babin Member Joined 2003 bcae1.com 2012-12-02 10:29 am #23 2012-12-02 10:29 am #23 That's a bit too low. How about a couple of 4.7 ohm resistors in parallel? seankane Member Joined 2010 2012-12-02 10:36 am #24 2012-12-02 10:36 am #24 Just found a roll I didnt know I had lol.....brb seankane Member Joined 2010 2012-12-02 10:41 am #25 2012-12-02 10:41 am #25 Replaced it and audio looks clean to me, thanks Perry. seankane Member Joined 2010 2012-12-02 8:53 pm #26 2012-12-02 8:53 pm #26 Ran the amp at medium to hard on the Punch 18" XLC sub for about an hour with no issues. Amp is working very good. This seller has 3 more with the same issues, think I am going to grab them all!!!! Prev 1 2 First Prev 2 of 2 Go to page Go Status Not open for further replies. Share: Facebook X (Twitter) LinkedIn Reddit Pinterest Tumblr WhatsApp Email Link
Lower would be better to see if that the only problem. You can use a leaded resistor if you have one of the correct value.
seankane Member Joined 2010 2012-12-02 10:29 am #22 2012-12-02 10:29 am #22 How about a .1 ohm source resistor for a rockford amp? P Perry Babin Member Joined 2003 bcae1.com 2012-12-02 10:29 am #23 2012-12-02 10:29 am #23 That's a bit too low. How about a couple of 4.7 ohm resistors in parallel? seankane Member Joined 2010 2012-12-02 10:36 am #24 2012-12-02 10:36 am #24 Just found a roll I didnt know I had lol.....brb seankane Member Joined 2010 2012-12-02 10:41 am #25 2012-12-02 10:41 am #25 Replaced it and audio looks clean to me, thanks Perry. seankane Member Joined 2010 2012-12-02 8:53 pm #26 2012-12-02 8:53 pm #26 Ran the amp at medium to hard on the Punch 18" XLC sub for about an hour with no issues. Amp is working very good. This seller has 3 more with the same issues, think I am going to grab them all!!!! Prev 1 2 First Prev 2 of 2 Go to page Go Status Not open for further replies. Share: Facebook X (Twitter) LinkedIn Reddit Pinterest Tumblr WhatsApp Email Link
P Perry Babin Member Joined 2003 bcae1.com 2012-12-02 10:29 am #23 2012-12-02 10:29 am #23 That's a bit too low. How about a couple of 4.7 ohm resistors in parallel? seankane Member Joined 2010 2012-12-02 10:36 am #24 2012-12-02 10:36 am #24 Just found a roll I didnt know I had lol.....brb seankane Member Joined 2010 2012-12-02 10:41 am #25 2012-12-02 10:41 am #25 Replaced it and audio looks clean to me, thanks Perry. seankane Member Joined 2010 2012-12-02 8:53 pm #26 2012-12-02 8:53 pm #26 Ran the amp at medium to hard on the Punch 18" XLC sub for about an hour with no issues. Amp is working very good. This seller has 3 more with the same issues, think I am going to grab them all!!!! Prev 1 2 First Prev 2 of 2 Go to page Go Status Not open for further replies. Share: Facebook X (Twitter) LinkedIn Reddit Pinterest Tumblr WhatsApp Email Link
seankane Member Joined 2010 2012-12-02 10:36 am #24 2012-12-02 10:36 am #24 Just found a roll I didnt know I had lol.....brb seankane Member Joined 2010 2012-12-02 10:41 am #25 2012-12-02 10:41 am #25 Replaced it and audio looks clean to me, thanks Perry. seankane Member Joined 2010 2012-12-02 8:53 pm #26 2012-12-02 8:53 pm #26 Ran the amp at medium to hard on the Punch 18" XLC sub for about an hour with no issues. Amp is working very good. This seller has 3 more with the same issues, think I am going to grab them all!!!! Prev 1 2 First Prev 2 of 2 Go to page Go Status Not open for further replies. Share: Facebook X (Twitter) LinkedIn Reddit Pinterest Tumblr WhatsApp Email Link
seankane Member Joined 2010 2012-12-02 10:41 am #25 2012-12-02 10:41 am #25 Replaced it and audio looks clean to me, thanks Perry. seankane Member Joined 2010 2012-12-02 8:53 pm #26 2012-12-02 8:53 pm #26 Ran the amp at medium to hard on the Punch 18" XLC sub for about an hour with no issues. Amp is working very good. This seller has 3 more with the same issues, think I am going to grab them all!!!! Prev 1 2 First Prev 2 of 2 Go to page Go Status Not open for further replies.
seankane Member Joined 2010 2012-12-02 8:53 pm #26 2012-12-02 8:53 pm #26 Ran the amp at medium to hard on the Punch 18" XLC sub for about an hour with no issues. Amp is working very good. This seller has 3 more with the same issues, think I am going to grab them all!!!!
Ran the amp at medium to hard on the Punch 18" XLC sub for about an hour with no issues. Amp is working very good. This seller has 3 more with the same issues, think I am going to grab them all!!!!
