jacco vermeulen said:
Jules
those caps are isnogood ....................... cause the lead spacing is off by 40 Mils.
Zen Mod said:
Jules
those caps are isnogood ....................... cause the lead spacing is off by 40 Mils.
...and you cannot fill them with beer...
(that way too OT, I'll stop now)
Manu said:
In your boots- I'll try to play safe ...... ask for another opinion, maybe I dreked something .......
hehe - "maybe" ..............
Manu said:
...and you cannot fill them with beer...
(that way too OT, I'll stop now)
but - yo can put them IN beer ........
HBarske said:I somehow knew those boards have a severe problem - it's impossible to get those output caps mounted...http://www.diyaudio.com/forums/attachment.php?s=&postid=1389684&stamp=1199317168
C'mon, those low quality Caps are aimed to be used in loudspeakers ...
😉
spavleski said:
hehe
same as - little birdie told me that someone ordered some loudspeaker intended Auricaps and Mundorfs......
😉
off topic mob
hm.....
I open this thread as official building thread, hoping that it will be more tidy and organized than previous one ......
I just realized that this thread now have more pages than previous,hysteric, one ........
naah......
seems that we just can't escape of our nature ....... and I tried so hard to be on topic
but - what can be expected of ppl who use speaker and filter caps as output ones ..........
hm.....
I open this thread as official building thread, hoping that it will be more tidy and organized than previous one ......
I just realized that this thread now have more pages than previous,hysteric, one ........
naah......
seems that we just can't escape of our nature ....... and I tried so hard to be on topic
but - what can be expected of ppl who use speaker and filter caps as output ones ..........
Zen Mod said:
In your boots- I'll try to play safe ...... ask for another opinion, maybe I dreked something .......
hehe - "maybe" ..............
edit :
I have few questions about Pumpkin/shunty :
1. regarding X-former : would a "2x30V" Trafo - which gives about 80V after bridge - be a good choice or not? Or should I rob my wife to buy a new one....
2. Regarding the electrolytics in Both Pumpkin and Shunty : is there any "crucial" places where it could be worth it to use some not-so-drekky ones ?
Manu
Manu said:
edit :
I have few questions about Pumpkin/shunty :
1. regarding X-former : would a "2x30V" Trafo - which gives about 80V after bridge - be a good choice or not? Or should I rob my wife to buy a new one....
2. Regarding the electrolytics in Both Pumpkin and Shunty : is there any "crucial" places where it could be worth it to use some not-so-drekky ones ?
Manu
1. you need +/-36V at output , after some pretty big voltage losses ;I can't recommend any voltage bellow +/- 50V on input , that's absolute minimum, and just in case that your mains voltage have no sags of -10%
2. on output of Shunty and local ones in P .
Manu, could you rob 2 more of those transformers for me from your wife's closet ? 😀
Choky,
When you say "local" I'm not sure what that means?
Mark
Choky,
When you say "local" I'm not sure what that means?
Mark
Will be using this one:
200VA o-core, 42-0-42V. I'd be able to source some more of those, but they have 230V primaries only.
200VA o-core, 42-0-42V. I'd be able to source some more of those, but they have 230V primaries only.
Manu said:
Mark :
I've tried ... but no way :
Wife's comment from the pic above: "I told ya not to touch my T..ransfomers!"
Or,
"Listen here! You can put your C..andle in that P..umpkin, but don't even think about messing with my T...ransformers!" 😀 😀 😀
"Listen here! You can put your C..andle in that P..umpkin, but don't even think about messing with my T...ransformers!" 😀 😀 😀
