thank gabanyayaya. i just read page 9. i should have got the 100k.
hmmph.
farnell had the neat little wago blocks and the whole thing was less expensive than mouser even though that's who i've used in the past - was afraid farnell would take forever but it came almost overnight. unfortunately you have a min. amount so now ill need to find pots at mouser.. ha ha ha.. part number anyone.
hmmph.
farnell had the neat little wago blocks and the whole thing was less expensive than mouser even though that's who i've used in the past - was afraid farnell would take forever but it came almost overnight. unfortunately you have a min. amount so now ill need to find pots at mouser.. ha ha ha.. part number anyone.
is possible to order some? (with components will be great for me, in argentina is impossible to get High Quality ones) 🙁
ok. i will purchase it 😀
Btw, wich is the diference between an Attenuator and an Pre? 😀
i mean, the purpose is the same, right? if i use an attenuator, dont need to use an pre.
How much the board+shipping to argentina? (20USD)?
Regards
Btw, wich is the diference between an Attenuator and an Pre? 😀
i mean, the purpose is the same, right? if i use an attenuator, dont need to use an pre.
How much the board+shipping to argentina? (20USD)?
Regards
The price will be as followed:
Professional 2-Layer PCB: $15
Worldwide shipping: $ 4
paypal fee: 3,9%
So together $19,74.
Please place your order to: lsapcb@gmx.com
The attenuator only reduce the output voltage of the source to the amp. No stages and parts between! 😉
Professional 2-Layer PCB: $15
Worldwide shipping: $ 4
paypal fee: 3,9%
So together $19,74.
Please place your order to: lsapcb@gmx.com
The attenuator only reduce the output voltage of the source to the amp. No stages and parts between! 😉
This would also replace standard volumn control right?
I am also looking to get in on the group buy for the B1 preamp
I am also looking to get in on the group buy for the B1 preamp
Oliver
Besides Alps pot, do you have any source for suitable 100k pot for the board. My 100K elchepo pot seams too 'small' for the board. Not enough wide to fit into each hole....
gianc
get the B1 shunt reg. buffer and you'll be surprise to know that this LSA board can be attached together with the B1 pcb board...
Besides Alps pot, do you have any source for suitable 100k pot for the board. My 100K elchepo pot seams too 'small' for the board. Not enough wide to fit into each hole....
gianc
get the B1 shunt reg. buffer and you'll be surprise to know that this LSA board can be attached together with the B1 pcb board...
Just use wires from the pot to the pcb. That is what I'm planning. Since I have two mono pots so I can have a form of balance control.
Was thinking that too....but wires.....wires..and wires...I like less wires specially in signal lines....if I put some effort to squeeze a bit I'll be manage to insert all pot leads into the hole....
Well...in this case the wires are not in the signal lines at all...that is the advantage of the lightspeed.
wooopss....yeah you're right then....no signal at all just voltage...this is what happens when you change normal function to abnormal function...😉
This is my LSA board and it can be attach nicely together with the B1 buffer board. Doesn't meant any thing but kinda cool.....
An externally hosted image should be here but it was not working when we last tested it.
Last edited:
Looks real cool 🙂
You could order a tandem 100k log at Conrad Electronic International
It has the ID No.: 449828-I5 😉
You could order a tandem 100k log at Conrad Electronic International
It has the ID No.: 449828-I5 😉
- Status
- Not open for further replies.