Hi everyone. I have a Neutrik A1 audio analyser that I recently bought. Unfortunately the power supply is faulty. Does anyone have a service manual with schematics for the unit please? I have looked throughly on line with no luck.
Thanks,
Mike
Thanks,
Mike
Hi Mark, thanks for the link. Unfortunately it is only the user manual which I had downloaded before. Luckily another member shared the service manual with me.
Thanks,
Mike
Thanks,
Mike
I have Neutrik A1 and A2, but now A1 is with my friend. A2 is broken. After I repaired it, it should work normally now. One of the faults is that the power supply has no power output. The reason is that a tantalum capacitor is broken and it is short-circuited. Hope it helps you.
Attachments
Neutrik A1 / A2 repairs
Hello all
Ken Ruecker here Service manager at NTi-Audio in Tigard , Oregon.
K.ruecker@nti-audio.com
Repairs and support are available for the A1 / A2 products.
We have A1 service manual but just one copy I can share.
A2 printed Service manuals are available for sale $65.00
Some limited parts are available.
Happy to share the knowledge base.
NTI is the management buy out of Original Neutrik Test division in Schaan Lichtenstein.
Hello all
Ken Ruecker here Service manager at NTi-Audio in Tigard , Oregon.
K.ruecker@nti-audio.com
Repairs and support are available for the A1 / A2 products.
We have A1 service manual but just one copy I can share.
A2 printed Service manuals are available for sale $65.00
Some limited parts are available.
Happy to share the knowledge base.
NTI is the management buy out of Original Neutrik Test division in Schaan Lichtenstein.
Hi, I also have an A1 with a "In- Output RMS Detector ERROR: Gain 01 LOW" Can I please share the SM if poss. Many thanks, Dave
Hi All, Has anyone any idea of a quick fix for the error on my Neutrik A1
"In- Output RMS Detector ERROR: Gain 01 LOW"
I would be most grateful for your help. Many thanks, Dave
"In- Output RMS Detector ERROR: Gain 01 LOW"
I would be most grateful for your help. Many thanks, Dave
NEUTRIK A2
I have the A2 for many years.
It displays now during calibration a message: Cal. source filters GAIN 02 HIGH.
Any ideas?
I noticed also that using W&F test and selecting IEC/DIN and 3000Hz I performed a test. I switched off the A2. Then I turned it on and selected W&F the frequency is at 3150Hz not at 3000Hz it didn't save may previous setting.
Is this normal or something is wrong with the memory?
Any help will be very appreciated?
Regards,
John.
SM may be can be found: NEUTRIK A2 SERVICE MANUAL | fresh-credit.bytestand.com
I have the A2 for many years.
It displays now during calibration a message: Cal. source filters GAIN 02 HIGH.
Any ideas?
I noticed also that using W&F test and selecting IEC/DIN and 3000Hz I performed a test. I switched off the A2. Then I turned it on and selected W&F the frequency is at 3150Hz not at 3000Hz it didn't save may previous setting.
Is this normal or something is wrong with the memory?
Any help will be very appreciated?
Regards,
John.
SM may be can be found: NEUTRIK A2 SERVICE MANUAL | fresh-credit.bytestand.com
If anyone need A1 service manual, please PM me. Also, if anyone have A1/2 serial card for sale, I am interested.
Regards,
Damir
Regards,
Damir
Hi .i have right now same error ,have you found finally some solution to repair this error?
Damir...Do you still have access to the Neutrik A1 Service Manual?....I would love to get a copy...Please Email Kvanwyk@indy.rr.com
Many Thanks!
Kevin
I would LOVE a copy of the service manual! I seem to have some sticky relays (at least I hope that's what it is), and a few minor gremlins. If someone could send it to kthefrog@hotmail.com I would be VERY grateful! Thanks