I was lookin for specifics to help someone,but all Kicker gives is a sealed and ported specs and not any general info in thier Manual.
On thier site it says the 06 which is rated the same as my 05:
Resonance frequency[fs],HZ = 34.0
Total Q-factor[qts] = .513
Equivalent volume[vas],ft3(l) = 2.2(62.5)
My trunk can fit around a 32X13X13 give or take a inch.
Ive had Bandpass in the past and love it........I looking for the most Boom for the Space I have.........I was wondering if 2 speakers in a sealed box would hit harder or one with the correctly designed box would hit harder.
I listen to technoBass notes/Rap and alot of others includin country..hehehe
But I like to have really low bass hittin capibility without losin alot of clarity for my country days.
😀
Thankx for all the help guys.
Joel
On thier site it says the 06 which is rated the same as my 05:
Resonance frequency[fs],HZ = 34.0
Total Q-factor[qts] = .513
Equivalent volume[vas],ft3(l) = 2.2(62.5)
My trunk can fit around a 32X13X13 give or take a inch.
Ive had Bandpass in the past and love it........I looking for the most Boom for the Space I have.........I was wondering if 2 speakers in a sealed box would hit harder or one with the correctly designed box would hit harder.
I listen to technoBass notes/Rap and alot of others includin country..hehehe
But I like to have really low bass hittin capibility without losin alot of clarity for my country days.
😀
Thankx for all the help guys.
Joel
I think your box is too small to go with bandpass...
I'd go with a ported enclosure of 13x13x32 tuned with a single 4" diameter full length precision port.
I'd go with a ported enclosure of 13x13x32 tuned with a single 4" diameter full length precision port.
I going to make a 2 piece box and make it 6th order!!
2 cubes each side........one to 35hz the other to 78hz.
Its just killin the ported box down low and up top by 3-5dbs and has a nice slope.....
What do you think???
Any programs out there to design or draw your box out good as Ill need to put it together somewhat in my trunk
2 cubes each side........one to 35hz the other to 78hz.
Its just killin the ported box down low and up top by 3-5dbs and has a nice slope.....
What do you think???
Any programs out there to design or draw your box out good as Ill need to put it together somewhat in my trunk
13x13x32 = 11.5x11.5x30.5 assuming you're using 0.75" walls.
That's 2.3 cu.ft internal net. Now remove driver volume, braces and port volume, you're probably at 2 cu.ft.
There's no way you're gonna fit 4 cubes in that space.
To design a box, you could use a CAD program...
A full length precision port is this :
http://www.partsexpress.com/pe/showdetl.cfm?&DID=7&Partnumber=268-352
That's 2.3 cu.ft internal net. Now remove driver volume, braces and port volume, you're probably at 2 cu.ft.
There's no way you're gonna fit 4 cubes in that space.
To design a box, you could use a CAD program...
A full length precision port is this :
http://www.partsexpress.com/pe/showdetl.cfm?&DID=7&Partnumber=268-352
Are there any free Cad Programs out???
I was thinkin about makin a 2 piece box and semi buildin it in the trunk
Looks like it is best just to build a ported box at around 40-44hz with a subsonic filter on it for 30-35hz with a 24db cutoff to avoid over excursion under that ........
What you think??
I was thinkin about makin a 2 piece box and semi buildin it in the trunk
Looks like it is best just to build a ported box at around 40-44hz with a subsonic filter on it for 30-35hz with a 24db cutoff to avoid over excursion under that ........
What you think??
Bah, I was thinking tuning it with a precision port like I've showed you. That would tune it around 27 Hz then add a subsonic at 25 Hz.
doin that I have a major cone excursion at 47-67hz at 750watts or more.
The rms is 750........I was tryin to get around 900 safely without over excursion???
The rms is 750........I was tryin to get around 900 safely without over excursion???
- Status
- Not open for further replies.