Marantz CD-65ll manual needed, or guide on removing the CDM-4/19

[data]

Hay guys

I desperately need help to swap the laser over from one Marantz payer to the other, the donor player is a CD-593 using a CDM-4 transport and the receiving player is a CD-65ll using the CDM-4/19

But I have no manuals and can't work out how to take the assembly apart on either of these 😕

Please help me...

 

[data]

I made a typo, It's a CD-65ll not 64...

 

[data]

Well I managed to swap the transport mech's over and am still getting the read error 😕

Don't know where to look now for the cause of the error

The guy I bought it from said it worked fine before he posted it to me

 

[SY]

Fixed.

 

[data]

Thanks for fixing up my typos SY

Now I just need the same to happen with this player 😉

 

[es44]

I'm sorry i can't help you with practical advise, but i have a schematic (with block diagram), for the 65II, maybe it is useful ?
Just say the word, and it's coming your way.

Best regards
Ebbe

 

[poynton]

Is (was) the cd593 a working player ?

If so, verify that both cdm4s are working.

Andy

 

[poynton]

I'm sorry i can't help you with practical advise, but i have a schematic (with block diagram), for the 65II, maybe it is useful ?
Just say the word, and it's coming your way.

Best regards
Ebbe

If you have a manual for the CD65II , please uoload it to OSTRIPPERs site so all can access it.

http://www.diyaudio.com/forums/showthread.php?s=&threadid=128658


Andy

 

[data]

es44, the that would be healpful as the issue is beyound the transport part 🙂
Thanks.

poynton, yes the 593 was working well, so the transport & laser are known good, and it turned out both are 4/19's

 

[poynton]

................. the transport & laser are known good...................

So what is it doing?
What are the symptoms?

Andy

 

[data]

Andy, It's just spinning the disk a little and then giving a red error light.

 

[poynton]

Go to service mode and report back.

I think Marantz uses the same procedure for all its cdps.

see attached.

Andy

 

[es44]

If you have a manual for the CD65II , please uoload it to OSTRIPPERs site so all can access it.

http://www.diyaudio.com/forums/showthread.php?s=&threadid=128658
Andy

Hi Andy.
I'd be happy to upload to Your database, and thank you very much for giving us all this great service.
But i don't seem to be able to connect ?

Best regards
Ebbe

Edit: Just realised it isn't Your place, but Ostrippers, thanks anyway for pointing me that way, and a great big THANKS to Ostripper for providing 🙂

 

[data]

poynton, that procedure doesn't seem to work with this one, does nothing when powering up like indicated in that guide...

 

[poynton]

It may be "hold play and next" while you power on

Andy

 

[data]

Nup...not that either, I have tried a few combos and haven't found it yet 😕

 

[data]

I'm sorry i can't help you with practical advise, but i have a schematic (with block diagram), for the 65II, maybe it is useful ?
Just say the word, and it's coming your way.

Best regards
Ebbe

Hay mate 🙂

Can I have that schematic (with block diagram) you offered?

Cheers 🙂

 

[es44]

Hay mate 🙂

Can I have that schematic (with block diagram) you offered?

Cheers 🙂

Certainly, do you have a valid email-address ?
(remember to "disguise" it if you put it here, just to prevent the spam-bots to get you ) 😀

 

[data]

Certainly, do you have a valid email-address ?
(remember to "disguise" it if you put it here, just to prevent the spam-bots to get you ) 😀

I have emailed my address to you.

Cheers mate 🙂

 

[data]

Well I'm lost as to how to enter service mode on this model, can't find anything on the net after searching all night