Hi all,
I thinks this fits in the power supply forum.
I was listening to my Revox B750 when I suddenly saw smoke, lots of smoke!
I instantly turned the amp off and pulled the plug out. We were afraid that the whole thing was on fire because of the smoke (the room was really full of it).
The smell of the smoke was really bad, my first tought was that a big cap blew.
After opening some windows, I opened the amp.
I could see the problem in an instant.
It has something to do with the voltage line selector.
Right now the selector is set to 240VAC (Belgium => 240VAC, 50Hz)
As you can see this 'thing' has caugt fire, the only thing I read on it was
"250V, fo 9MHz"
What is this component?
Also: the fuse is not blown and the music kept playing when smoke was coming out.
I thinks this fits in the power supply forum.
I was listening to my Revox B750 when I suddenly saw smoke, lots of smoke!
I instantly turned the amp off and pulled the plug out. We were afraid that the whole thing was on fire because of the smoke (the room was really full of it).
The smell of the smoke was really bad, my first tought was that a big cap blew.
After opening some windows, I opened the amp.
I could see the problem in an instant.
It has something to do with the voltage line selector.
Right now the selector is set to 240VAC (Belgium => 240VAC, 50Hz)
As you can see this 'thing' has caugt fire, the only thing I read on it was
"250V, fo 9MHz"
What is this component?
Also: the fuse is not blown and the music kept playing when smoke was coming out.
Looks like a noise suppression capacitor, X or Y type.
The dielectric got compromised, just snip the leads and remove it.
If you really want, replace it with the proper type, around 100nF (try to see the rating of the original one). Type X if it does not go to ground (most likely). Type Y if it does.
The dielectric got compromised, just snip the leads and remove it.
If you really want, replace it with the proper type, around 100nF (try to see the rating of the original one). Type X if it does not go to ground (most likely). Type Y if it does.
Looks like a noise suppression capacitor, X or Y type.
The dielectric got compromised, just snip the leads and remove it.
If you really want, replace it with the proper type, around 100nF (try to see the rating of the original one). Type X if it does not go to ground (most likely). Type Y if it does.
The dielectric got compromised, just snip the leads and remove it.
If you really want, replace it with the proper type, around 100nF (try to see the rating of the original one). Type X if it does not go to ground (most likely). Type Y if it does.
Will a WIMA MKP capacitor do the job?
An externally hosted image should be here but it was not working when we last tested it.
I've used them in some amps, they are alot smaller than the cap I blew.
I've got my hands on the schematic of this amp. Maybe this could say what value it was.
NO!
Has to be an X-rated type (not what you think...🙂).
Try to get X1, if not X2 is ok.
http://www.vishay.com/docs/28117/mkp3361.pdf
You can also safely leave it out, at the risk of picking up some electrical noise through the mains feed.
I'm not familiar with X or Y type capacitors.
I went on a searchs in my recycled component. And I found one it has X2 printed on it, the value is 330nF
I went on a searchs in my recycled component. And I found one it has X2 printed on it, the value is 330nF
I had the same problem a few days ago. i must need to change component or i can use this amp without ? voltage must be set to 240 VAC?
100nF indeed, thanks discrete!
This schematic is wrong (it's for MK I and not MK II). However the value of .1uF (100nF) is the same as for MK II. Here you have it for MK II ...
An externally hosted image should be here but it was not working when we last tested it.
I've just bought B750 MK II in working and untouched condition. Soon after powering it happened.
Just take care of all foil pieces that can shorcircuit board somewhere inside (vacuum cleaner will do it for you).
Just take care of all foil pieces that can shorcircuit board somewhere inside (vacuum cleaner will do it for you).
Original (RFI) filtering capacitor inside was class X2 Evox Rifa (acquired by Kemet Corp in 2007) PME271M610 with 0,1 uF and rated voltage of 275 VAC.
I've replaced it with Wima MP3-X2 with of same values.
I've replaced it with Wima MP3-X2 with of same values.
- Status
- Not open for further replies.