This guide is a compilation of the information from [wiki=Krell_KSA-50_clone_Building_Guide]%[/wiki]
| border="0" cellspacing="5"
|-
| Name || Krell KSA 50 Clone (by Jan Dupont)
|-
| Type || Solid State
|-
| Application || High Bandwidth Amplifier
|-
| Class || A
|-
| Approx Cost || $2,000 USD (new)
|-
|
|-
| Designer || Dan D'agositino (from Krell); clone by Dan Dupont
|-
| Thread || [wiki=Krell_KSA-50_clone_Building_Guide]%[/wiki]
|-
[h=The Project]%1[/h]
[h=Introduction]%2[/h]
This is a clone Krell's KSA 50 amp which helped put the company on the map during the late 80s and early 90s. It is a pure class A amp and delivers a very sweet sound.
[h=Goals]%2[/h]
N/A
[h=Specifications]%2[/h]
border="0" cellpadding="2" cellspacing="0"
|-
| class="tcat" | Name
| class="tcat" | Description
|-
| Volatge Gain || value
|-
| Bandwidth || Value
|-
| Phase || Value
|-
| Sensitivity || 8 Ohm: 50 (17 dbW), 4 Ohm: 100, 2 Ohm: 200W
|-
| S/N Ratio || Unknown
|-
| Rated Consumption || 100W
|-
| Idle Consumption || 100W
|-
| Harmonic Distortion || Unknown
|-
| Harmonic Spectrum || Unknown
|-
| Square/Step response || Unknown
|-
| Stability || Unknown
|-
| Output configurations || Can it be bridged? Parallel drive?
|-
| Output Impedance || Unknown
[h=Schematic/Blueprint]%2[/h]
PDF Version of Schematic
[h=Bill of Materials]%2[/h]
Bill Of Materials
[h=Simulations and Analysis]%2[/h]
Note yet complete
[h=Construction (Steps / Tips / Notes)]%1[/h]
Is there anything peculiar about the design that a builder might want to know about? List them here? Or do you just want to give us a step-by-step build plan; that works too.
[h=Project Modifications]%2[/h]
Do you have some small modifications to suggest for the project that could improve it? Please list them and tell us why they improve the design. If this is discussed in a thread, please link the thread URL here....
[h=Modification 1]%3[/h]
Cross the streams!
[h=Modification 2]%3[/h]
Install a flux capacitor!
[h=Reviews]%1[/h]
[h=Review 1]%2[/h]
Rock on!
[h=Review 2]%2[/h]
Duuuude.....
[h=Build Threads]%1[/h]
Have you built this project? If so, please add the URL to the thread that you started to show off your build.
[h=Related Group Buys]%1[/h]
|-
| Name || Krell KSA 50 Clone (by Jan Dupont)
|-
| Type || Solid State
|-
| Application || High Bandwidth Amplifier
|-
| Class || A
|-
| Approx Cost || $2,000 USD (new)
|-
|
|-
| Designer || Dan D'agositino (from Krell); clone by Dan Dupont
|-
| Thread || [wiki=Krell_KSA-50_clone_Building_Guide]%[/wiki]
|-
[h=The Project]%1[/h]
[h=Introduction]%2[/h]
This is a clone Krell's KSA 50 amp which helped put the company on the map during the late 80s and early 90s. It is a pure class A amp and delivers a very sweet sound.
[h=Goals]%2[/h]
N/A
[h=Specifications]%2[/h]
|-
| class="tcat" | Name
| class="tcat" | Description
|-
| Volatge Gain || value
|-
| Bandwidth || Value
|-
| Phase || Value
|-
| Sensitivity || 8 Ohm: 50 (17 dbW), 4 Ohm: 100, 2 Ohm: 200W
|-
| S/N Ratio || Unknown
|-
| Rated Consumption || 100W
|-
| Idle Consumption || 100W
|-
| Harmonic Distortion || Unknown
|-
| Harmonic Spectrum || Unknown
|-
| Square/Step response || Unknown
|-
| Stability || Unknown
|-
| Output configurations || Can it be bridged? Parallel drive?
|-
| Output Impedance || Unknown
[h=Schematic/Blueprint]%2[/h]
PDF Version of Schematic
[h=Bill of Materials]%2[/h]
Bill Of Materials
[h=Simulations and Analysis]%2[/h]
Note yet complete
[h=Construction (Steps / Tips / Notes)]%1[/h]
Is there anything peculiar about the design that a builder might want to know about? List them here? Or do you just want to give us a step-by-step build plan; that works too.
[h=Project Modifications]%2[/h]
Do you have some small modifications to suggest for the project that could improve it? Please list them and tell us why they improve the design. If this is discussed in a thread, please link the thread URL here....
[h=Modification 1]%3[/h]
Cross the streams!
[h=Modification 2]%3[/h]
Install a flux capacitor!
[h=Reviews]%1[/h]
[h=Review 1]%2[/h]
Rock on!
[h=Review 2]%2[/h]
Duuuude.....
[h=Build Threads]%1[/h]
Have you built this project? If so, please add the URL to the thread that you started to show off your build.
- URL to my uber build 1 thread
- URL to my super dooper build 2 thread!!!
[h=Related Group Buys]%1[/h]
- Thread 1234
- GroupBuy😛SU