Are you sure that you had 0v on the end of R110 that is not connected to pin 3 of U102?
P Perry Babin Member Joined 2003 bcae1.com 2011-10-06 2:29 am #61 2011-10-06 2:29 am #61 Are you sure that you had 0v on the end of R110 that is not connected to pin 3 of U102? ••• More options Share T timwebb Member Joined 2010 2011-10-06 2:39 am #62 2011-10-06 2:39 am #62 rechecked and its 0v ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2011-10-06 12:40 pm #63 2011-10-06 12:40 pm #63 On U102, if you solder a jumper between pin 2 and pin 6, does the voltage on pin 3 go to 0v? ••• More options Share T timwebb Member Joined 2010 2011-10-06 9:31 pm #64 2011-10-06 9:31 pm #64 yes its 0v. ••• More options Share T timwebb Member Joined 2010 2011-10-07 7:35 pm #65 2011-10-07 7:35 pm #65 Defective ic? ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2011-10-07 8:09 pm #66 2011-10-07 8:09 pm #66 With the jumper in place, what is the DC voltage on the speaker terminals for that channel? ••• More options Share T timwebb Member Joined 2010 2011-10-08 6:20 am #67 2011-10-08 6:20 am #67 -28.2 ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2011-10-08 4:34 pm #68 2011-10-08 4:34 pm #68 Do you have any module plugged into this amp? ••• More options Share T timwebb Member Joined 2010 2011-10-08 5:50 pm #69 2011-10-08 5:50 pm #69 No ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2011-10-08 7:05 pm #70 2011-10-08 7:05 pm #70 Remove Q109 and Q111. Does the DC on the output drop to near 0v? ••• More options Share T timwebb Member Joined 2010 2011-10-08 10:01 pm #71 2011-10-08 10:01 pm #71 Yes I have 0v now ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2011-10-09 12:27 am #72 2011-10-09 12:27 am #72 On the two TL431s in this channel, what is the DC voltage with the black probe on pin 2 and the red probe on pin 1? Don't slip and short the pins. ••• More options Share T timwebb Member Joined 2010 2011-10-09 8:36 pm #73 2011-10-09 8:36 pm #73 +2.51v on both ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2011-10-09 8:39 pm #74 2011-10-09 8:39 pm #74 Check the two drivers that you removed. Do both have two good junctions? Is there any reverse leakage or leakage from collector to emitter? ••• More options Share T timwebb Member Joined 2010 2011-10-09 10:21 pm #75 2011-10-09 10:21 pm #75 both test good. i get no readings across the pins. i would like to replace them any way. Last edited: 2011-10-09 10:48 pm ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2011-10-10 1:19 am #76 2011-10-10 1:19 am #76 Remove the jumper on the TL071 and post the voltage on pins 2, 3 and 6. Leave those drivers out of the circuit. ••• More options Share T timwebb Member Joined 2010 2011-10-10 2:02 am #77 2011-10-10 2:02 am #77 2- -15.56 3- -13.5 6- 13.8 ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2011-10-10 2:08 am #78 2011-10-10 2:08 am #78 In the future, don't use a hyphen as a separator. Post the DC voltage on all 8 pins of U101 near the RCA jacks. ••• More options Share T timwebb Member Joined 2010 2011-10-10 2:20 am #79 2011-10-10 2:20 am #79 1. -13.7 2. -13.6 3. -13.5 4. -15.1 5. -13.7 6. -13.5 7. .-13.6 8. 14.8 ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2011-10-10 2:25 am #80 2011-10-10 2:25 am #80 Did you repair the open ground in this area that was discussed earlier? If not, find it and repair the open trace. ••• More options Share Prev 1 2 3 4 5 Next First Prev 4 of 5 Go to page Go Next Last Show hidden low quality content Status This old topic is closed. If you want to reopen this topic, contact a moderator using the "Report Post" button. Share: Facebook Twitter Reddit Pinterest Tumblr WhatsApp Email Share Link Home General Interest Car Audio kicker xs100 Top Bottom
T timwebb Member Joined 2010 2011-10-06 2:39 am #62 2011-10-06 2:39 am #62 rechecked and its 0v ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2011-10-06 12:40 pm #63 2011-10-06 12:40 pm #63 On U102, if you solder a jumper between pin 2 and pin 6, does the voltage on pin 3 go to 0v? ••• More options Share T timwebb Member Joined 2010 2011-10-06 9:31 pm #64 2011-10-06 9:31 pm #64 yes its 0v. ••• More options Share T timwebb Member Joined 2010 2011-10-07 7:35 pm #65 2011-10-07 7:35 pm #65 Defective ic? ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2011-10-07 8:09 pm #66 2011-10-07 8:09 pm #66 With the jumper in place, what is the DC voltage on the speaker terminals for that channel? ••• More options Share T timwebb Member Joined 2010 2011-10-08 6:20 am #67 2011-10-08 6:20 am #67 -28.2 ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2011-10-08 4:34 pm #68 2011-10-08 4:34 pm #68 Do you have any module plugged into this amp? ••• More options Share T timwebb Member Joined 2010 2011-10-08 5:50 pm #69 2011-10-08 5:50 pm #69 No ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2011-10-08 7:05 pm #70 2011-10-08 7:05 pm #70 Remove Q109 and Q111. Does the DC on the output drop to near 0v? ••• More options Share T timwebb Member Joined 2010 2011-10-08 10:01 pm #71 2011-10-08 10:01 pm #71 Yes I have 0v now ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2011-10-09 12:27 am #72 2011-10-09 12:27 am #72 On the two TL431s in this channel, what is the DC voltage with the black probe on pin 2 and the red probe on pin 1? Don't slip and short the pins. ••• More options Share T timwebb Member Joined 2010 2011-10-09 8:36 pm #73 2011-10-09 8:36 pm #73 +2.51v on both ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2011-10-09 8:39 pm #74 2011-10-09 8:39 pm #74 Check the two drivers that you removed. Do both have two good junctions? Is there any reverse leakage or leakage from collector to emitter? ••• More options Share T timwebb Member Joined 2010 2011-10-09 10:21 pm #75 2011-10-09 10:21 pm #75 both test good. i get no readings across the pins. i would like to replace them any way. Last edited: 2011-10-09 10:48 pm ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2011-10-10 1:19 am #76 2011-10-10 1:19 am #76 Remove the jumper on the TL071 and post the voltage on pins 2, 3 and 6. Leave those drivers out of the circuit. ••• More options Share T timwebb Member Joined 2010 2011-10-10 2:02 am #77 2011-10-10 2:02 am #77 2- -15.56 3- -13.5 6- 13.8 ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2011-10-10 2:08 am #78 2011-10-10 2:08 am #78 In the future, don't use a hyphen as a separator. Post the DC voltage on all 8 pins of U101 near the RCA jacks. ••• More options Share T timwebb Member Joined 2010 2011-10-10 2:20 am #79 2011-10-10 2:20 am #79 1. -13.7 2. -13.6 3. -13.5 4. -15.1 5. -13.7 6. -13.5 7. .-13.6 8. 14.8 ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2011-10-10 2:25 am #80 2011-10-10 2:25 am #80 Did you repair the open ground in this area that was discussed earlier? If not, find it and repair the open trace. ••• More options Share Prev 1 2 3 4 5 Next First Prev 4 of 5 Go to page Go Next Last Show hidden low quality content Status This old topic is closed. If you want to reopen this topic, contact a moderator using the "Report Post" button. Share: Facebook Twitter Reddit Pinterest Tumblr WhatsApp Email Share Link Home General Interest Car Audio kicker xs100 Top Bottom
P Perry Babin Member Joined 2003 bcae1.com 2011-10-06 12:40 pm #63 2011-10-06 12:40 pm #63 On U102, if you solder a jumper between pin 2 and pin 6, does the voltage on pin 3 go to 0v? ••• More options Share T timwebb Member Joined 2010 2011-10-06 9:31 pm #64 2011-10-06 9:31 pm #64 yes its 0v. ••• More options Share T timwebb Member Joined 2010 2011-10-07 7:35 pm #65 2011-10-07 7:35 pm #65 Defective ic? ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2011-10-07 8:09 pm #66 2011-10-07 8:09 pm #66 With the jumper in place, what is the DC voltage on the speaker terminals for that channel? ••• More options Share T timwebb Member Joined 2010 2011-10-08 6:20 am #67 2011-10-08 6:20 am #67 -28.2 ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2011-10-08 4:34 pm #68 2011-10-08 4:34 pm #68 Do you have any module plugged into this amp? ••• More options Share T timwebb Member Joined 2010 2011-10-08 5:50 pm #69 2011-10-08 5:50 pm #69 No ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2011-10-08 7:05 pm #70 2011-10-08 7:05 pm #70 Remove Q109 and Q111. Does the DC on the output drop to near 0v? ••• More options Share T timwebb Member Joined 2010 2011-10-08 10:01 pm #71 2011-10-08 10:01 pm #71 Yes I have 0v now ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2011-10-09 12:27 am #72 2011-10-09 12:27 am #72 On the two TL431s in this channel, what is the DC voltage with the black probe on pin 2 and the red probe on pin 1? Don't slip and short the pins. ••• More options Share T timwebb Member Joined 2010 2011-10-09 8:36 pm #73 2011-10-09 8:36 pm #73 +2.51v on both ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2011-10-09 8:39 pm #74 2011-10-09 8:39 pm #74 Check the two drivers that you removed. Do both have two good junctions? Is there any reverse leakage or leakage from collector to emitter? ••• More options Share T timwebb Member Joined 2010 2011-10-09 10:21 pm #75 2011-10-09 10:21 pm #75 both test good. i get no readings across the pins. i would like to replace them any way. Last edited: 2011-10-09 10:48 pm ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2011-10-10 1:19 am #76 2011-10-10 1:19 am #76 Remove the jumper on the TL071 and post the voltage on pins 2, 3 and 6. Leave those drivers out of the circuit. ••• More options Share T timwebb Member Joined 2010 2011-10-10 2:02 am #77 2011-10-10 2:02 am #77 2- -15.56 3- -13.5 6- 13.8 ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2011-10-10 2:08 am #78 2011-10-10 2:08 am #78 In the future, don't use a hyphen as a separator. Post the DC voltage on all 8 pins of U101 near the RCA jacks. ••• More options Share T timwebb Member Joined 2010 2011-10-10 2:20 am #79 2011-10-10 2:20 am #79 1. -13.7 2. -13.6 3. -13.5 4. -15.1 5. -13.7 6. -13.5 7. .-13.6 8. 14.8 ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2011-10-10 2:25 am #80 2011-10-10 2:25 am #80 Did you repair the open ground in this area that was discussed earlier? If not, find it and repair the open trace. ••• More options Share Prev 1 2 3 4 5 Next First Prev 4 of 5 Go to page Go Next Last Show hidden low quality content Status This old topic is closed. If you want to reopen this topic, contact a moderator using the "Report Post" button. Share: Facebook Twitter Reddit Pinterest Tumblr WhatsApp Email Share Link Home General Interest Car Audio kicker xs100 Top Bottom
T timwebb Member Joined 2010 2011-10-06 9:31 pm #64 2011-10-06 9:31 pm #64 yes its 0v. ••• More options Share T timwebb Member Joined 2010 2011-10-07 7:35 pm #65 2011-10-07 7:35 pm #65 Defective ic? ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2011-10-07 8:09 pm #66 2011-10-07 8:09 pm #66 With the jumper in place, what is the DC voltage on the speaker terminals for that channel? ••• More options Share T timwebb Member Joined 2010 2011-10-08 6:20 am #67 2011-10-08 6:20 am #67 -28.2 ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2011-10-08 4:34 pm #68 2011-10-08 4:34 pm #68 Do you have any module plugged into this amp? ••• More options Share T timwebb Member Joined 2010 2011-10-08 5:50 pm #69 2011-10-08 5:50 pm #69 No ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2011-10-08 7:05 pm #70 2011-10-08 7:05 pm #70 Remove Q109 and Q111. Does the DC on the output drop to near 0v? ••• More options Share T timwebb Member Joined 2010 2011-10-08 10:01 pm #71 2011-10-08 10:01 pm #71 Yes I have 0v now ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2011-10-09 12:27 am #72 2011-10-09 12:27 am #72 On the two TL431s in this channel, what is the DC voltage with the black probe on pin 2 and the red probe on pin 1? Don't slip and short the pins. ••• More options Share T timwebb Member Joined 2010 2011-10-09 8:36 pm #73 2011-10-09 8:36 pm #73 +2.51v on both ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2011-10-09 8:39 pm #74 2011-10-09 8:39 pm #74 Check the two drivers that you removed. Do both have two good junctions? Is there any reverse leakage or leakage from collector to emitter? ••• More options Share T timwebb Member Joined 2010 2011-10-09 10:21 pm #75 2011-10-09 10:21 pm #75 both test good. i get no readings across the pins. i would like to replace them any way. Last edited: 2011-10-09 10:48 pm ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2011-10-10 1:19 am #76 2011-10-10 1:19 am #76 Remove the jumper on the TL071 and post the voltage on pins 2, 3 and 6. Leave those drivers out of the circuit. ••• More options Share T timwebb Member Joined 2010 2011-10-10 2:02 am #77 2011-10-10 2:02 am #77 2- -15.56 3- -13.5 6- 13.8 ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2011-10-10 2:08 am #78 2011-10-10 2:08 am #78 In the future, don't use a hyphen as a separator. Post the DC voltage on all 8 pins of U101 near the RCA jacks. ••• More options Share T timwebb Member Joined 2010 2011-10-10 2:20 am #79 2011-10-10 2:20 am #79 1. -13.7 2. -13.6 3. -13.5 4. -15.1 5. -13.7 6. -13.5 7. .-13.6 8. 14.8 ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2011-10-10 2:25 am #80 2011-10-10 2:25 am #80 Did you repair the open ground in this area that was discussed earlier? If not, find it and repair the open trace. ••• More options Share Prev 1 2 3 4 5 Next First Prev 4 of 5 Go to page Go Next Last Show hidden low quality content Status This old topic is closed. If you want to reopen this topic, contact a moderator using the "Report Post" button. Share: Facebook Twitter Reddit Pinterest Tumblr WhatsApp Email Share Link Home General Interest Car Audio kicker xs100 Top Bottom
T timwebb Member Joined 2010 2011-10-07 7:35 pm #65 2011-10-07 7:35 pm #65 Defective ic? ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2011-10-07 8:09 pm #66 2011-10-07 8:09 pm #66 With the jumper in place, what is the DC voltage on the speaker terminals for that channel? ••• More options Share T timwebb Member Joined 2010 2011-10-08 6:20 am #67 2011-10-08 6:20 am #67 -28.2 ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2011-10-08 4:34 pm #68 2011-10-08 4:34 pm #68 Do you have any module plugged into this amp? ••• More options Share T timwebb Member Joined 2010 2011-10-08 5:50 pm #69 2011-10-08 5:50 pm #69 No ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2011-10-08 7:05 pm #70 2011-10-08 7:05 pm #70 Remove Q109 and Q111. Does the DC on the output drop to near 0v? ••• More options Share T timwebb Member Joined 2010 2011-10-08 10:01 pm #71 2011-10-08 10:01 pm #71 Yes I have 0v now ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2011-10-09 12:27 am #72 2011-10-09 12:27 am #72 On the two TL431s in this channel, what is the DC voltage with the black probe on pin 2 and the red probe on pin 1? Don't slip and short the pins. ••• More options Share T timwebb Member Joined 2010 2011-10-09 8:36 pm #73 2011-10-09 8:36 pm #73 +2.51v on both ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2011-10-09 8:39 pm #74 2011-10-09 8:39 pm #74 Check the two drivers that you removed. Do both have two good junctions? Is there any reverse leakage or leakage from collector to emitter? ••• More options Share T timwebb Member Joined 2010 2011-10-09 10:21 pm #75 2011-10-09 10:21 pm #75 both test good. i get no readings across the pins. i would like to replace them any way. Last edited: 2011-10-09 10:48 pm ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2011-10-10 1:19 am #76 2011-10-10 1:19 am #76 Remove the jumper on the TL071 and post the voltage on pins 2, 3 and 6. Leave those drivers out of the circuit. ••• More options Share T timwebb Member Joined 2010 2011-10-10 2:02 am #77 2011-10-10 2:02 am #77 2- -15.56 3- -13.5 6- 13.8 ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2011-10-10 2:08 am #78 2011-10-10 2:08 am #78 In the future, don't use a hyphen as a separator. Post the DC voltage on all 8 pins of U101 near the RCA jacks. ••• More options Share T timwebb Member Joined 2010 2011-10-10 2:20 am #79 2011-10-10 2:20 am #79 1. -13.7 2. -13.6 3. -13.5 4. -15.1 5. -13.7 6. -13.5 7. .-13.6 8. 14.8 ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2011-10-10 2:25 am #80 2011-10-10 2:25 am #80 Did you repair the open ground in this area that was discussed earlier? If not, find it and repair the open trace. ••• More options Share Prev 1 2 3 4 5 Next First Prev 4 of 5 Go to page Go Next Last Show hidden low quality content Status This old topic is closed. If you want to reopen this topic, contact a moderator using the "Report Post" button. Share: Facebook Twitter Reddit Pinterest Tumblr WhatsApp Email Share Link Home General Interest Car Audio kicker xs100 Top Bottom
P Perry Babin Member Joined 2003 bcae1.com 2011-10-07 8:09 pm #66 2011-10-07 8:09 pm #66 With the jumper in place, what is the DC voltage on the speaker terminals for that channel? ••• More options Share T timwebb Member Joined 2010 2011-10-08 6:20 am #67 2011-10-08 6:20 am #67 -28.2 ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2011-10-08 4:34 pm #68 2011-10-08 4:34 pm #68 Do you have any module plugged into this amp? ••• More options Share T timwebb Member Joined 2010 2011-10-08 5:50 pm #69 2011-10-08 5:50 pm #69 No ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2011-10-08 7:05 pm #70 2011-10-08 7:05 pm #70 Remove Q109 and Q111. Does the DC on the output drop to near 0v? ••• More options Share T timwebb Member Joined 2010 2011-10-08 10:01 pm #71 2011-10-08 10:01 pm #71 Yes I have 0v now ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2011-10-09 12:27 am #72 2011-10-09 12:27 am #72 On the two TL431s in this channel, what is the DC voltage with the black probe on pin 2 and the red probe on pin 1? Don't slip and short the pins. ••• More options Share T timwebb Member Joined 2010 2011-10-09 8:36 pm #73 2011-10-09 8:36 pm #73 +2.51v on both ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2011-10-09 8:39 pm #74 2011-10-09 8:39 pm #74 Check the two drivers that you removed. Do both have two good junctions? Is there any reverse leakage or leakage from collector to emitter? ••• More options Share T timwebb Member Joined 2010 2011-10-09 10:21 pm #75 2011-10-09 10:21 pm #75 both test good. i get no readings across the pins. i would like to replace them any way. Last edited: 2011-10-09 10:48 pm ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2011-10-10 1:19 am #76 2011-10-10 1:19 am #76 Remove the jumper on the TL071 and post the voltage on pins 2, 3 and 6. Leave those drivers out of the circuit. ••• More options Share T timwebb Member Joined 2010 2011-10-10 2:02 am #77 2011-10-10 2:02 am #77 2- -15.56 3- -13.5 6- 13.8 ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2011-10-10 2:08 am #78 2011-10-10 2:08 am #78 In the future, don't use a hyphen as a separator. Post the DC voltage on all 8 pins of U101 near the RCA jacks. ••• More options Share T timwebb Member Joined 2010 2011-10-10 2:20 am #79 2011-10-10 2:20 am #79 1. -13.7 2. -13.6 3. -13.5 4. -15.1 5. -13.7 6. -13.5 7. .-13.6 8. 14.8 ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2011-10-10 2:25 am #80 2011-10-10 2:25 am #80 Did you repair the open ground in this area that was discussed earlier? If not, find it and repair the open trace. ••• More options Share Prev 1 2 3 4 5 Next First Prev 4 of 5 Go to page Go Next Last Show hidden low quality content Status This old topic is closed. If you want to reopen this topic, contact a moderator using the "Report Post" button. Share: Facebook Twitter Reddit Pinterest Tumblr WhatsApp Email Share Link Home General Interest Car Audio kicker xs100 Top Bottom
T timwebb Member Joined 2010 2011-10-08 6:20 am #67 2011-10-08 6:20 am #67 -28.2 ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2011-10-08 4:34 pm #68 2011-10-08 4:34 pm #68 Do you have any module plugged into this amp? ••• More options Share T timwebb Member Joined 2010 2011-10-08 5:50 pm #69 2011-10-08 5:50 pm #69 No ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2011-10-08 7:05 pm #70 2011-10-08 7:05 pm #70 Remove Q109 and Q111. Does the DC on the output drop to near 0v? ••• More options Share T timwebb Member Joined 2010 2011-10-08 10:01 pm #71 2011-10-08 10:01 pm #71 Yes I have 0v now ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2011-10-09 12:27 am #72 2011-10-09 12:27 am #72 On the two TL431s in this channel, what is the DC voltage with the black probe on pin 2 and the red probe on pin 1? Don't slip and short the pins. ••• More options Share T timwebb Member Joined 2010 2011-10-09 8:36 pm #73 2011-10-09 8:36 pm #73 +2.51v on both ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2011-10-09 8:39 pm #74 2011-10-09 8:39 pm #74 Check the two drivers that you removed. Do both have two good junctions? Is there any reverse leakage or leakage from collector to emitter? ••• More options Share T timwebb Member Joined 2010 2011-10-09 10:21 pm #75 2011-10-09 10:21 pm #75 both test good. i get no readings across the pins. i would like to replace them any way. Last edited: 2011-10-09 10:48 pm ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2011-10-10 1:19 am #76 2011-10-10 1:19 am #76 Remove the jumper on the TL071 and post the voltage on pins 2, 3 and 6. Leave those drivers out of the circuit. ••• More options Share T timwebb Member Joined 2010 2011-10-10 2:02 am #77 2011-10-10 2:02 am #77 2- -15.56 3- -13.5 6- 13.8 ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2011-10-10 2:08 am #78 2011-10-10 2:08 am #78 In the future, don't use a hyphen as a separator. Post the DC voltage on all 8 pins of U101 near the RCA jacks. ••• More options Share T timwebb Member Joined 2010 2011-10-10 2:20 am #79 2011-10-10 2:20 am #79 1. -13.7 2. -13.6 3. -13.5 4. -15.1 5. -13.7 6. -13.5 7. .-13.6 8. 14.8 ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2011-10-10 2:25 am #80 2011-10-10 2:25 am #80 Did you repair the open ground in this area that was discussed earlier? If not, find it and repair the open trace. ••• More options Share Prev 1 2 3 4 5 Next First Prev 4 of 5 Go to page Go Next Last Show hidden low quality content Status This old topic is closed. If you want to reopen this topic, contact a moderator using the "Report Post" button. Share: Facebook Twitter Reddit Pinterest Tumblr WhatsApp Email Share Link Home General Interest Car Audio kicker xs100 Top Bottom
P Perry Babin Member Joined 2003 bcae1.com 2011-10-08 4:34 pm #68 2011-10-08 4:34 pm #68 Do you have any module plugged into this amp? ••• More options Share T timwebb Member Joined 2010 2011-10-08 5:50 pm #69 2011-10-08 5:50 pm #69 No ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2011-10-08 7:05 pm #70 2011-10-08 7:05 pm #70 Remove Q109 and Q111. Does the DC on the output drop to near 0v? ••• More options Share T timwebb Member Joined 2010 2011-10-08 10:01 pm #71 2011-10-08 10:01 pm #71 Yes I have 0v now ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2011-10-09 12:27 am #72 2011-10-09 12:27 am #72 On the two TL431s in this channel, what is the DC voltage with the black probe on pin 2 and the red probe on pin 1? Don't slip and short the pins. ••• More options Share T timwebb Member Joined 2010 2011-10-09 8:36 pm #73 2011-10-09 8:36 pm #73 +2.51v on both ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2011-10-09 8:39 pm #74 2011-10-09 8:39 pm #74 Check the two drivers that you removed. Do both have two good junctions? Is there any reverse leakage or leakage from collector to emitter? ••• More options Share T timwebb Member Joined 2010 2011-10-09 10:21 pm #75 2011-10-09 10:21 pm #75 both test good. i get no readings across the pins. i would like to replace them any way. Last edited: 2011-10-09 10:48 pm ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2011-10-10 1:19 am #76 2011-10-10 1:19 am #76 Remove the jumper on the TL071 and post the voltage on pins 2, 3 and 6. Leave those drivers out of the circuit. ••• More options Share T timwebb Member Joined 2010 2011-10-10 2:02 am #77 2011-10-10 2:02 am #77 2- -15.56 3- -13.5 6- 13.8 ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2011-10-10 2:08 am #78 2011-10-10 2:08 am #78 In the future, don't use a hyphen as a separator. Post the DC voltage on all 8 pins of U101 near the RCA jacks. ••• More options Share T timwebb Member Joined 2010 2011-10-10 2:20 am #79 2011-10-10 2:20 am #79 1. -13.7 2. -13.6 3. -13.5 4. -15.1 5. -13.7 6. -13.5 7. .-13.6 8. 14.8 ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2011-10-10 2:25 am #80 2011-10-10 2:25 am #80 Did you repair the open ground in this area that was discussed earlier? If not, find it and repair the open trace. ••• More options Share Prev 1 2 3 4 5 Next First Prev 4 of 5 Go to page Go Next Last Show hidden low quality content Status This old topic is closed. If you want to reopen this topic, contact a moderator using the "Report Post" button. Share: Facebook Twitter Reddit Pinterest Tumblr WhatsApp Email Share Link Home General Interest Car Audio kicker xs100 Top Bottom
T timwebb Member Joined 2010 2011-10-08 5:50 pm #69 2011-10-08 5:50 pm #69 No ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2011-10-08 7:05 pm #70 2011-10-08 7:05 pm #70 Remove Q109 and Q111. Does the DC on the output drop to near 0v? ••• More options Share T timwebb Member Joined 2010 2011-10-08 10:01 pm #71 2011-10-08 10:01 pm #71 Yes I have 0v now ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2011-10-09 12:27 am #72 2011-10-09 12:27 am #72 On the two TL431s in this channel, what is the DC voltage with the black probe on pin 2 and the red probe on pin 1? Don't slip and short the pins. ••• More options Share T timwebb Member Joined 2010 2011-10-09 8:36 pm #73 2011-10-09 8:36 pm #73 +2.51v on both ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2011-10-09 8:39 pm #74 2011-10-09 8:39 pm #74 Check the two drivers that you removed. Do both have two good junctions? Is there any reverse leakage or leakage from collector to emitter? ••• More options Share T timwebb Member Joined 2010 2011-10-09 10:21 pm #75 2011-10-09 10:21 pm #75 both test good. i get no readings across the pins. i would like to replace them any way. Last edited: 2011-10-09 10:48 pm ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2011-10-10 1:19 am #76 2011-10-10 1:19 am #76 Remove the jumper on the TL071 and post the voltage on pins 2, 3 and 6. Leave those drivers out of the circuit. ••• More options Share T timwebb Member Joined 2010 2011-10-10 2:02 am #77 2011-10-10 2:02 am #77 2- -15.56 3- -13.5 6- 13.8 ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2011-10-10 2:08 am #78 2011-10-10 2:08 am #78 In the future, don't use a hyphen as a separator. Post the DC voltage on all 8 pins of U101 near the RCA jacks. ••• More options Share T timwebb Member Joined 2010 2011-10-10 2:20 am #79 2011-10-10 2:20 am #79 1. -13.7 2. -13.6 3. -13.5 4. -15.1 5. -13.7 6. -13.5 7. .-13.6 8. 14.8 ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2011-10-10 2:25 am #80 2011-10-10 2:25 am #80 Did you repair the open ground in this area that was discussed earlier? If not, find it and repair the open trace. ••• More options Share Prev 1 2 3 4 5 Next First Prev 4 of 5 Go to page Go Next Last Show hidden low quality content Status This old topic is closed. If you want to reopen this topic, contact a moderator using the "Report Post" button. Share: Facebook Twitter Reddit Pinterest Tumblr WhatsApp Email Share Link Home General Interest Car Audio kicker xs100 Top Bottom
P Perry Babin Member Joined 2003 bcae1.com 2011-10-08 7:05 pm #70 2011-10-08 7:05 pm #70 Remove Q109 and Q111. Does the DC on the output drop to near 0v? ••• More options Share T timwebb Member Joined 2010 2011-10-08 10:01 pm #71 2011-10-08 10:01 pm #71 Yes I have 0v now ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2011-10-09 12:27 am #72 2011-10-09 12:27 am #72 On the two TL431s in this channel, what is the DC voltage with the black probe on pin 2 and the red probe on pin 1? Don't slip and short the pins. ••• More options Share T timwebb Member Joined 2010 2011-10-09 8:36 pm #73 2011-10-09 8:36 pm #73 +2.51v on both ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2011-10-09 8:39 pm #74 2011-10-09 8:39 pm #74 Check the two drivers that you removed. Do both have two good junctions? Is there any reverse leakage or leakage from collector to emitter? ••• More options Share T timwebb Member Joined 2010 2011-10-09 10:21 pm #75 2011-10-09 10:21 pm #75 both test good. i get no readings across the pins. i would like to replace them any way. Last edited: 2011-10-09 10:48 pm ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2011-10-10 1:19 am #76 2011-10-10 1:19 am #76 Remove the jumper on the TL071 and post the voltage on pins 2, 3 and 6. Leave those drivers out of the circuit. ••• More options Share T timwebb Member Joined 2010 2011-10-10 2:02 am #77 2011-10-10 2:02 am #77 2- -15.56 3- -13.5 6- 13.8 ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2011-10-10 2:08 am #78 2011-10-10 2:08 am #78 In the future, don't use a hyphen as a separator. Post the DC voltage on all 8 pins of U101 near the RCA jacks. ••• More options Share T timwebb Member Joined 2010 2011-10-10 2:20 am #79 2011-10-10 2:20 am #79 1. -13.7 2. -13.6 3. -13.5 4. -15.1 5. -13.7 6. -13.5 7. .-13.6 8. 14.8 ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2011-10-10 2:25 am #80 2011-10-10 2:25 am #80 Did you repair the open ground in this area that was discussed earlier? If not, find it and repair the open trace. ••• More options Share Prev 1 2 3 4 5 Next First Prev 4 of 5 Go to page Go Next Last Show hidden low quality content Status This old topic is closed. If you want to reopen this topic, contact a moderator using the "Report Post" button. Share: Facebook Twitter Reddit Pinterest Tumblr WhatsApp Email Share Link Home General Interest Car Audio kicker xs100 Top Bottom
T timwebb Member Joined 2010 2011-10-08 10:01 pm #71 2011-10-08 10:01 pm #71 Yes I have 0v now ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2011-10-09 12:27 am #72 2011-10-09 12:27 am #72 On the two TL431s in this channel, what is the DC voltage with the black probe on pin 2 and the red probe on pin 1? Don't slip and short the pins. ••• More options Share T timwebb Member Joined 2010 2011-10-09 8:36 pm #73 2011-10-09 8:36 pm #73 +2.51v on both ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2011-10-09 8:39 pm #74 2011-10-09 8:39 pm #74 Check the two drivers that you removed. Do both have two good junctions? Is there any reverse leakage or leakage from collector to emitter? ••• More options Share T timwebb Member Joined 2010 2011-10-09 10:21 pm #75 2011-10-09 10:21 pm #75 both test good. i get no readings across the pins. i would like to replace them any way. Last edited: 2011-10-09 10:48 pm ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2011-10-10 1:19 am #76 2011-10-10 1:19 am #76 Remove the jumper on the TL071 and post the voltage on pins 2, 3 and 6. Leave those drivers out of the circuit. ••• More options Share T timwebb Member Joined 2010 2011-10-10 2:02 am #77 2011-10-10 2:02 am #77 2- -15.56 3- -13.5 6- 13.8 ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2011-10-10 2:08 am #78 2011-10-10 2:08 am #78 In the future, don't use a hyphen as a separator. Post the DC voltage on all 8 pins of U101 near the RCA jacks. ••• More options Share T timwebb Member Joined 2010 2011-10-10 2:20 am #79 2011-10-10 2:20 am #79 1. -13.7 2. -13.6 3. -13.5 4. -15.1 5. -13.7 6. -13.5 7. .-13.6 8. 14.8 ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2011-10-10 2:25 am #80 2011-10-10 2:25 am #80 Did you repair the open ground in this area that was discussed earlier? If not, find it and repair the open trace. ••• More options Share Prev 1 2 3 4 5 Next First Prev 4 of 5 Go to page Go Next Last Show hidden low quality content Status This old topic is closed. If you want to reopen this topic, contact a moderator using the "Report Post" button. Share: Facebook Twitter Reddit Pinterest Tumblr WhatsApp Email Share Link Home General Interest Car Audio kicker xs100 Top Bottom
P Perry Babin Member Joined 2003 bcae1.com 2011-10-09 12:27 am #72 2011-10-09 12:27 am #72 On the two TL431s in this channel, what is the DC voltage with the black probe on pin 2 and the red probe on pin 1? Don't slip and short the pins. ••• More options Share T timwebb Member Joined 2010 2011-10-09 8:36 pm #73 2011-10-09 8:36 pm #73 +2.51v on both ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2011-10-09 8:39 pm #74 2011-10-09 8:39 pm #74 Check the two drivers that you removed. Do both have two good junctions? Is there any reverse leakage or leakage from collector to emitter? ••• More options Share T timwebb Member Joined 2010 2011-10-09 10:21 pm #75 2011-10-09 10:21 pm #75 both test good. i get no readings across the pins. i would like to replace them any way. Last edited: 2011-10-09 10:48 pm ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2011-10-10 1:19 am #76 2011-10-10 1:19 am #76 Remove the jumper on the TL071 and post the voltage on pins 2, 3 and 6. Leave those drivers out of the circuit. ••• More options Share T timwebb Member Joined 2010 2011-10-10 2:02 am #77 2011-10-10 2:02 am #77 2- -15.56 3- -13.5 6- 13.8 ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2011-10-10 2:08 am #78 2011-10-10 2:08 am #78 In the future, don't use a hyphen as a separator. Post the DC voltage on all 8 pins of U101 near the RCA jacks. ••• More options Share T timwebb Member Joined 2010 2011-10-10 2:20 am #79 2011-10-10 2:20 am #79 1. -13.7 2. -13.6 3. -13.5 4. -15.1 5. -13.7 6. -13.5 7. .-13.6 8. 14.8 ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2011-10-10 2:25 am #80 2011-10-10 2:25 am #80 Did you repair the open ground in this area that was discussed earlier? If not, find it and repair the open trace. ••• More options Share Prev 1 2 3 4 5 Next First Prev 4 of 5 Go to page Go Next Last Show hidden low quality content Status This old topic is closed. If you want to reopen this topic, contact a moderator using the "Report Post" button. Share: Facebook Twitter Reddit Pinterest Tumblr WhatsApp Email Share Link Home General Interest Car Audio kicker xs100 Top Bottom
On the two TL431s in this channel, what is the DC voltage with the black probe on pin 2 and the red probe on pin 1? Don't slip and short the pins.
T timwebb Member Joined 2010 2011-10-09 8:36 pm #73 2011-10-09 8:36 pm #73 +2.51v on both ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2011-10-09 8:39 pm #74 2011-10-09 8:39 pm #74 Check the two drivers that you removed. Do both have two good junctions? Is there any reverse leakage or leakage from collector to emitter? ••• More options Share T timwebb Member Joined 2010 2011-10-09 10:21 pm #75 2011-10-09 10:21 pm #75 both test good. i get no readings across the pins. i would like to replace them any way. Last edited: 2011-10-09 10:48 pm ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2011-10-10 1:19 am #76 2011-10-10 1:19 am #76 Remove the jumper on the TL071 and post the voltage on pins 2, 3 and 6. Leave those drivers out of the circuit. ••• More options Share T timwebb Member Joined 2010 2011-10-10 2:02 am #77 2011-10-10 2:02 am #77 2- -15.56 3- -13.5 6- 13.8 ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2011-10-10 2:08 am #78 2011-10-10 2:08 am #78 In the future, don't use a hyphen as a separator. Post the DC voltage on all 8 pins of U101 near the RCA jacks. ••• More options Share T timwebb Member Joined 2010 2011-10-10 2:20 am #79 2011-10-10 2:20 am #79 1. -13.7 2. -13.6 3. -13.5 4. -15.1 5. -13.7 6. -13.5 7. .-13.6 8. 14.8 ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2011-10-10 2:25 am #80 2011-10-10 2:25 am #80 Did you repair the open ground in this area that was discussed earlier? If not, find it and repair the open trace. ••• More options Share Prev 1 2 3 4 5 Next First Prev 4 of 5 Go to page Go Next Last Show hidden low quality content Status This old topic is closed. If you want to reopen this topic, contact a moderator using the "Report Post" button. Share: Facebook Twitter Reddit Pinterest Tumblr WhatsApp Email Share Link Home General Interest Car Audio kicker xs100
P Perry Babin Member Joined 2003 bcae1.com 2011-10-09 8:39 pm #74 2011-10-09 8:39 pm #74 Check the two drivers that you removed. Do both have two good junctions? Is there any reverse leakage or leakage from collector to emitter? ••• More options Share T timwebb Member Joined 2010 2011-10-09 10:21 pm #75 2011-10-09 10:21 pm #75 both test good. i get no readings across the pins. i would like to replace them any way. Last edited: 2011-10-09 10:48 pm ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2011-10-10 1:19 am #76 2011-10-10 1:19 am #76 Remove the jumper on the TL071 and post the voltage on pins 2, 3 and 6. Leave those drivers out of the circuit. ••• More options Share T timwebb Member Joined 2010 2011-10-10 2:02 am #77 2011-10-10 2:02 am #77 2- -15.56 3- -13.5 6- 13.8 ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2011-10-10 2:08 am #78 2011-10-10 2:08 am #78 In the future, don't use a hyphen as a separator. Post the DC voltage on all 8 pins of U101 near the RCA jacks. ••• More options Share T timwebb Member Joined 2010 2011-10-10 2:20 am #79 2011-10-10 2:20 am #79 1. -13.7 2. -13.6 3. -13.5 4. -15.1 5. -13.7 6. -13.5 7. .-13.6 8. 14.8 ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2011-10-10 2:25 am #80 2011-10-10 2:25 am #80 Did you repair the open ground in this area that was discussed earlier? If not, find it and repair the open trace. ••• More options Share Prev 1 2 3 4 5 Next First Prev 4 of 5 Go to page Go Next Last Show hidden low quality content Status This old topic is closed. If you want to reopen this topic, contact a moderator using the "Report Post" button. Share: Facebook Twitter Reddit Pinterest Tumblr WhatsApp Email Share Link Home General Interest Car Audio kicker xs100
Check the two drivers that you removed. Do both have two good junctions? Is there any reverse leakage or leakage from collector to emitter?
T timwebb Member Joined 2010 2011-10-09 10:21 pm #75 2011-10-09 10:21 pm #75 both test good. i get no readings across the pins. i would like to replace them any way. Last edited: 2011-10-09 10:48 pm ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2011-10-10 1:19 am #76 2011-10-10 1:19 am #76 Remove the jumper on the TL071 and post the voltage on pins 2, 3 and 6. Leave those drivers out of the circuit. ••• More options Share T timwebb Member Joined 2010 2011-10-10 2:02 am #77 2011-10-10 2:02 am #77 2- -15.56 3- -13.5 6- 13.8 ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2011-10-10 2:08 am #78 2011-10-10 2:08 am #78 In the future, don't use a hyphen as a separator. Post the DC voltage on all 8 pins of U101 near the RCA jacks. ••• More options Share T timwebb Member Joined 2010 2011-10-10 2:20 am #79 2011-10-10 2:20 am #79 1. -13.7 2. -13.6 3. -13.5 4. -15.1 5. -13.7 6. -13.5 7. .-13.6 8. 14.8 ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2011-10-10 2:25 am #80 2011-10-10 2:25 am #80 Did you repair the open ground in this area that was discussed earlier? If not, find it and repair the open trace. ••• More options Share Prev 1 2 3 4 5 Next First Prev 4 of 5 Go to page Go Next Last Show hidden low quality content Status This old topic is closed. If you want to reopen this topic, contact a moderator using the "Report Post" button. Share: Facebook Twitter Reddit Pinterest Tumblr WhatsApp Email Share Link
P Perry Babin Member Joined 2003 bcae1.com 2011-10-10 1:19 am #76 2011-10-10 1:19 am #76 Remove the jumper on the TL071 and post the voltage on pins 2, 3 and 6. Leave those drivers out of the circuit. ••• More options Share T timwebb Member Joined 2010 2011-10-10 2:02 am #77 2011-10-10 2:02 am #77 2- -15.56 3- -13.5 6- 13.8 ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2011-10-10 2:08 am #78 2011-10-10 2:08 am #78 In the future, don't use a hyphen as a separator. Post the DC voltage on all 8 pins of U101 near the RCA jacks. ••• More options Share T timwebb Member Joined 2010 2011-10-10 2:20 am #79 2011-10-10 2:20 am #79 1. -13.7 2. -13.6 3. -13.5 4. -15.1 5. -13.7 6. -13.5 7. .-13.6 8. 14.8 ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2011-10-10 2:25 am #80 2011-10-10 2:25 am #80 Did you repair the open ground in this area that was discussed earlier? If not, find it and repair the open trace. ••• More options Share Prev 1 2 3 4 5 Next First Prev 4 of 5 Go to page Go Next Last Show hidden low quality content Status This old topic is closed. If you want to reopen this topic, contact a moderator using the "Report Post" button. Share: Facebook Twitter Reddit Pinterest Tumblr WhatsApp Email Share Link
Remove the jumper on the TL071 and post the voltage on pins 2, 3 and 6. Leave those drivers out of the circuit.
T timwebb Member Joined 2010 2011-10-10 2:02 am #77 2011-10-10 2:02 am #77 2- -15.56 3- -13.5 6- 13.8 ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2011-10-10 2:08 am #78 2011-10-10 2:08 am #78 In the future, don't use a hyphen as a separator. Post the DC voltage on all 8 pins of U101 near the RCA jacks. ••• More options Share T timwebb Member Joined 2010 2011-10-10 2:20 am #79 2011-10-10 2:20 am #79 1. -13.7 2. -13.6 3. -13.5 4. -15.1 5. -13.7 6. -13.5 7. .-13.6 8. 14.8 ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2011-10-10 2:25 am #80 2011-10-10 2:25 am #80 Did you repair the open ground in this area that was discussed earlier? If not, find it and repair the open trace. ••• More options Share Prev 1 2 3 4 5 Next First Prev 4 of 5 Go to page Go Next Last Show hidden low quality content Status This old topic is closed. If you want to reopen this topic, contact a moderator using the "Report Post" button. Share: Facebook Twitter Reddit Pinterest Tumblr WhatsApp Email Share Link
P Perry Babin Member Joined 2003 bcae1.com 2011-10-10 2:08 am #78 2011-10-10 2:08 am #78 In the future, don't use a hyphen as a separator. Post the DC voltage on all 8 pins of U101 near the RCA jacks. ••• More options Share T timwebb Member Joined 2010 2011-10-10 2:20 am #79 2011-10-10 2:20 am #79 1. -13.7 2. -13.6 3. -13.5 4. -15.1 5. -13.7 6. -13.5 7. .-13.6 8. 14.8 ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2011-10-10 2:25 am #80 2011-10-10 2:25 am #80 Did you repair the open ground in this area that was discussed earlier? If not, find it and repair the open trace. ••• More options Share Prev 1 2 3 4 5 Next First Prev 4 of 5 Go to page Go Next Last Show hidden low quality content Status This old topic is closed. If you want to reopen this topic, contact a moderator using the "Report Post" button. Share: Facebook Twitter Reddit Pinterest Tumblr WhatsApp Email Share Link
In the future, don't use a hyphen as a separator. Post the DC voltage on all 8 pins of U101 near the RCA jacks.
T timwebb Member Joined 2010 2011-10-10 2:20 am #79 2011-10-10 2:20 am #79 1. -13.7 2. -13.6 3. -13.5 4. -15.1 5. -13.7 6. -13.5 7. .-13.6 8. 14.8 ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2011-10-10 2:25 am #80 2011-10-10 2:25 am #80 Did you repair the open ground in this area that was discussed earlier? If not, find it and repair the open trace. ••• More options Share Prev 1 2 3 4 5 Next First Prev 4 of 5 Go to page Go Next Last Show hidden low quality content Status This old topic is closed. If you want to reopen this topic, contact a moderator using the "Report Post" button.
P Perry Babin Member Joined 2003 bcae1.com 2011-10-10 2:25 am #80 2011-10-10 2:25 am #80 Did you repair the open ground in this area that was discussed earlier? If not, find it and repair the open trace. ••• More options Share
Did you repair the open ground in this area that was discussed earlier? If not, find it and repair the open trace.