Hi guys,
I have been looking at the Kemet Pegi electrolytic series of capacitors for a RH84 SE Valve amp project.
Has anyone used these before they seem to have good specs and long life?
The C1 47uF 450v is in the PSU and I could go with that or a Motor Run Capacitor.
PEG124YL2470QL1 | KEMET 47μF Electrolytic Capacitor 450V dc, Through Hole - PEG124YL2470QL1 | RS Components
Capacitance: 47 uF
CapacitanceTolerance: -10/+30%
Voltage DC: 450 VDC
TemperatureRange: -40/+105°C
RatedTemperature: 105°C
Life: 22000 Hrs
Resistance:1200 mOhms (100Hz 20C), 530 mOhms (100kHz 20C)
Ripple Current: 0.377 Amps (100Hz 125C), 2.4 Amps (5kHz 60C), 0.89 Amps (5kHz 125C)
Leakage Current: 63 uA (5min 20°C) 0.377 Amps (100Hz 125C),
Inductance: 17 nH (ESL)
Any thoughts and opinions welcome
Motor Run Polyprop 46UF 450v
https://uk.rs-online.com/web/p/products/9119421/
Thanks
I have been looking at the Kemet Pegi electrolytic series of capacitors for a RH84 SE Valve amp project.
Has anyone used these before they seem to have good specs and long life?
The C1 47uF 450v is in the PSU and I could go with that or a Motor Run Capacitor.
PEG124YL2470QL1 | KEMET 47μF Electrolytic Capacitor 450V dc, Through Hole - PEG124YL2470QL1 | RS Components
Capacitance: 47 uF
CapacitanceTolerance: -10/+30%
Voltage DC: 450 VDC
TemperatureRange: -40/+105°C
RatedTemperature: 105°C
Life: 22000 Hrs
Resistance:1200 mOhms (100Hz 20C), 530 mOhms (100kHz 20C)
Ripple Current: 0.377 Amps (100Hz 125C), 2.4 Amps (5kHz 60C), 0.89 Amps (5kHz 125C)
Leakage Current: 63 uA (5min 20°C) 0.377 Amps (100Hz 125C),
Inductance: 17 nH (ESL)
Any thoughts and opinions welcome
Motor Run Polyprop 46UF 450v
https://uk.rs-online.com/web/p/products/9119421/
Thanks
Kemet's Rifa series capacitors are the highest quality capacitors available along with Epcos Sikorel in my opinion. I highly suspect that you can find a better capacitor.
Thanks for the reply, I am a bit confused did you mean I can or cannot find a better capacitor?
Thanks
Lee
Thanks
Lee
Thanks for the reply, I am a bit confused did you mean I can or cannot find a better capacitor?
Thanks
Lee
I think that you cannot find a better axial capacitor within same specs. Only part that I'm aware of that specifies 20k hours at 105°C is Nichicon PX but they are not axial.
I thought you are going to use Kemet PEGL in PSU filter section. Because it is polarized electrolyte capacitor. If you're trying to find a capacitor for signal coupling/dc blocking you better to look for film capacitors.
Hi , yes I can use it in the psu section. I was thinking about using them for the other caps.
Would you not use them on the audio section as the design specified electrolytic apart from one cap.
Thanks
Would you not use them on the audio section as the design specified electrolytic apart from one cap.
Thanks
- Home
- Design & Build
- Parts
- Kemhet PEGI Electrolytic Series Caps