How high in the RF range?
You can pick up a nice surplus Tektronix active FET probe. High-impedance in, plugs into a BNC jack, drives 50 Ohms.
You'll need to get the separate external power supply for it, though - it uses small, latchable LEMO connectors for the power,
that are built into some TEK 'scopes, but probably not your analyzer.
-3dB bandwidth of 500 MHz, and I think also one that's 1 or 1.2 GHz.
I know a site where you can download the manuals for free, if wanted a look at the technical specs, schematic and servicing info
before you decide. New, they were pretty $$$ back in the day...Jim Williams actually wrote a whole app note about 'gotchas' to look for
with 'scope probes (AN-47?) and it included a 'how-to' for making your own. He requested that his bosses get him one for a project at work,
but they wouldn't approve the $500.
If you get one second-hand, though, make sure they give a money-back guarantee and state explicitly that it's a working unit :
- to keep the input impedance high, and input C low (0.2 pF), that tip goes straight to the base of a FET, and it is very prone being blown
by ESD, or exceeding the input voltage spec.
Far as the power supply goes, you can buy a couple of those LEMO connectors, and build your own.
That was your design article, wasn't it? - "Build a Wide-Bandwidth Power Supply" -
The problem I have is that all this equipment has 50 ohms inputs. I understand where that comes from, but I'd rather have either a switchable 50 ohms/high impedance, or a high impedance input buffer or something like that. Several vector network analyzers have switchable 50 ohms / 1Meg inputs, for example.
Do any of you know whether there is a solution to this or am I chasing ghosts?
Jan
You can pick up a nice surplus Tektronix active FET probe. High-impedance in, plugs into a BNC jack, drives 50 Ohms.
You'll need to get the separate external power supply for it, though - it uses small, latchable LEMO connectors for the power,
that are built into some TEK 'scopes, but probably not your analyzer.
-3dB bandwidth of 500 MHz, and I think also one that's 1 or 1.2 GHz.
I know a site where you can download the manuals for free, if wanted a look at the technical specs, schematic and servicing info
before you decide. New, they were pretty $$$ back in the day...Jim Williams actually wrote a whole app note about 'gotchas' to look for
with 'scope probes (AN-47?) and it included a 'how-to' for making your own. He requested that his bosses get him one for a project at work,
but they wouldn't approve the $500.
If you get one second-hand, though, make sure they give a money-back guarantee and state explicitly that it's a working unit :
- to keep the input impedance high, and input C low (0.2 pF), that tip goes straight to the base of a FET, and it is very prone being blown
by ESD, or exceeding the input voltage spec.
Far as the power supply goes, you can buy a couple of those LEMO connectors, and build your own.
That was your design article, wasn't it? - "Build a Wide-Bandwidth Power Supply" -
Last edited:
http://cds.linear.com/docs/en/application-note/an47fa.pdf all known back then!
DIY 1GHz* Active Probe for Under 20$**: 5 Steps (with Pictures) there are still some new designs coming out.
DIY 1GHz* Active Probe for Under 20$**: 5 Steps (with Pictures) there are still some new designs coming out.
He requested that his bosses get him one for a project at work,
but they wouldn't approve the $500.
Virtually all of Jim's lab was used we had access to the military surplus dump in Taunton MA and blank MIT purchase orders. Then there was Eli's in Somerville.
Oh man, that would have been amazing!!!we had access to the military surplus dump
Having access to Bell's used stuff would also be amazing. So many schools and hobbyists / small businesses could really use that stuff.
-Chris
Oh man, that would have been amazing!!!
-Chris
It was to die for, circa 1970 literally hangars full of stuff. It's where all the folk lore started about folks reassembling Nike missiles, etc. IIRC someone found a pure platinum ingot inside some tool box.
It's where all the folk lore started about folks reassembling Nike missiles, etc. IIRC someone found a pure platinum ingot inside some tool box.
Really doesn't matter if it's true, still paints a wildly entertaining picture.
http://cds.linear.com/docs/en/application-note/an47fa.pdf all known back then!
DIY 1GHz* Active Probe for Under 20$**: 5 Steps (with Pictures) there are still some new designs coming out.
Yes pretty much anything from Jim is a treasure trove for designers. You can't avoid learning something from every read.
Jan
Really doesn't matter if it's true, still paints a wildly entertaining picture.
It wasn't, I tracked down one of the legends not that long ago, just another Sci-Fi nerd and it was all made up. It turns out it's the worshipers that want the legends to be true that propagate them.
Last edited:
http://cds.linear.com/docs/en/application-note/an47fa.pdf all known back then!
DIY 1GHz* Active Probe for Under 20$**: 5 Steps (with Pictures) there are still some new designs coming out.
OTOH, one of Scott's AD4817's and the ADI eval board with a +/-5V Silentswitcher will fix it too. Much cheaper ;-)
Jan
Yes but the narrow band filter (down to 1Hz in the R&S) will block the harmonics, right?
Jan
If it is a multiple conversion swept LO analyzer the 1Hz would be on the IF and the harmonics from the mixer still show up since they are all converted down to the IF frequency. A 20Hz to 100MHz SA does not have an oscillator that goes down to 20Hz.
Last edited:
This preamp has 'AD4817' written all over it. Some of the data sheet values, and the option for 500Gohm input Z are identical to the AD4817:
High-Z Spectrum Analyzer Amplifier, 1MOhm, 4pF, FETAMP1 | eBay
For that money, I can build one myself
And I can build in some gain.
Jan
High-Z Spectrum Analyzer Amplifier, 1MOhm, 4pF, FETAMP1 | eBay
For that money, I can build one myself
And I can build in some gain.
Jan
Last edited:
OTOH, one of Scott's AD4817's and the ADI eval board with a +/-5V Silentswitcher will fix it too. Much cheaper ;-)
Jan
One in stock, free delivery
ADA4817-2ACP-EBZ | Analog Devices ADA4817-2ACP-EBZ, Operational Amplifier Evaluation Board for LFCSP16 for ADA4817-2 | Analog Devices
- Status
- Not open for further replies.
- Home
- Member Areas
- The Lounge
- John Curl's Blowtorch preamplifier part II