PCBs and FETs yes.
Inductors you would have to ask at the other GB thread.
http://www.diyaudio.com/forums/group-buys/216993-fastron-inductor-group-buy-jg-filter-buffer.html
Patrick
Inductors you would have to ask at the other GB thread.
http://www.diyaudio.com/forums/group-buys/216993-fastron-inductor-group-buy-jg-filter-buffer.html
Patrick
Thanks for the payments.
Latest status updated.
https://docs.google.com/spreadsheet/ccc?key=0AvxEzxwAYdm9dFFoc2hJUm9rcmR3UkJ6Q0k3dC05LXc
Cheers,
WK
Latest status updated.
https://docs.google.com/spreadsheet/ccc?key=0AvxEzxwAYdm9dFFoc2hJUm9rcmR3UkJ6Q0k3dC05LXc
Cheers,
WK
New GB info in the inductor/parts kit thread:
Fran
So we are now ready to take payment.
There is now one extra of each component included in the parts kit as suggested by EUVL, and we have allowed for a few extra inductors to ensure matching works out OK. I've gone for flat rate postage to simplify matters further. As I said before, any monies left over at the end will be donated to diyaudio - without which we would not be getting any of this stuff.
Please visit the spreadsheet (link in my sig) to see your personal total amount. Please send your payment to my paypal (francis dot morrin at gmail dot com) and make sure to include your DIYAUDIO USERNAME, NAME AND POSTAL ADDRESS. That last bit is very important!!!!! I'll update the spreadsheet regularly.
I haven't offered a tracking postal service. If anyone needs this service, please shoot me a mail/pm so I can figure out the cost.
Fran
Work in progress
Thank you for your patience. Here is some progress update.
1. JFET Matching: BF862 matching is done. Expect J111 matching to be finished this week.
2. Test Fixture: Done, see attached.
3. Soldering: pending
4. Testing: pending
Cheers,
WK
Thank you for your patience. Here is some progress update.
1. JFET Matching: BF862 matching is done. Expect J111 matching to be finished this week.
2. Test Fixture: Done, see attached.
3. Soldering: pending
4. Testing: pending
Cheers,
WK
Attachments
The rest of the parts arrived from Mouser today too, so I will make up the kits over the next while.
Fran
Fran
Folks,
In preparation for the arrival, I have rolled out a new board based on the 9023 chip with mounting positions for the JG filter. Sample shown is for my own use but if there is sufficient interest and permission from Joachim I could make more. Will come fully loaded (DAC side only). Chip is powered by 3.6V from an on-board low noise reg with options for external supply if preferred. External supply is 5-12V for chip and +/-9V to +/-15V for the filter module. Can direct connect if filter is not used. This will help with comparisons
Cheers, Acko
In preparation for the arrival, I have rolled out a new board based on the 9023 chip with mounting positions for the JG filter. Sample shown is for my own use but if there is sufficient interest and permission from Joachim I could make more. Will come fully loaded (DAC side only). Chip is powered by 3.6V from an on-board low noise reg with options for external supply if preferred. External supply is 5-12V for chip and +/-9V to +/-15V for the filter module. Can direct connect if filter is not used. This will help with comparisons
Cheers, Acko
Attachments
AKD23
Hi All,
Thanks for the interest!
Do not wish to flood this thread with mine. You may order this part off-the-plan from my website below. Free shipping for early birds! Just go to the AKD23 section. DAC BOM is same as ESS specs. Schematic, BOM and 9023 datasheet supplied with purchase.
Cheers, Acko
Hi All,
Thanks for the interest!
Do not wish to flood this thread with mine. You may order this part off-the-plan from my website below. Free shipping for early birds! Just go to the AKD23 section. DAC BOM is same as ESS specs. Schematic, BOM and 9023 datasheet supplied with purchase.
Cheers, Acko
Hi acko ! Please go ahead. The buffer is already in the public domain anyway. Your board looks good.
- Home
- Group Buys
- Joachim Gerhard Filter Buffer for ES9022