hello everyone,
I put the modules UCH180HG together, my setup, softstart to Mono HG power supply, to the UCD180HG, with TR180 transformer.
i get very low output, ears to the speaker you can hear something, but very very low. if i higher the preamp volume, the sound will be not louder but will get a distortion in de sound, input to high i think.
any suggestions what it could do wrong, i followed the hypex papers correctly..
is D6 a led on the 180HG print? must it give light when turn on?
i have voltage on the print, that's ok. but is module defect?
i hope someone can help.
thx in advance
Hans
I put the modules UCH180HG together, my setup, softstart to Mono HG power supply, to the UCD180HG, with TR180 transformer.
i get very low output, ears to the speaker you can hear something, but very very low. if i higher the preamp volume, the sound will be not louder but will get a distortion in de sound, input to high i think.
any suggestions what it could do wrong, i followed the hypex papers correctly..
is D6 a led on the 180HG print? must it give light when turn on?
i have voltage on the print, that's ok. but is module defect?
i hope someone can help.
thx in advance
Hans
Problem solved ! shortcut in the speaker output.
I take the cables off, amplifier off/on with cables.
Working.....
I take the cables off, amplifier off/on with cables.
Working.....
I have the same problem, no sound from one of the modules, and very low sound from the other.
I've measured voltage on the modules, and it looked ok. So it seems like the problem is related to the output cables, like thread starter.
But I cannot see anything wrong with my speaker/signal outputs or cables.
The solderings look fine, and all cables are checked and double-checked.
Any tips?
I've measured voltage on the modules, and it looked ok. So it seems like the problem is related to the output cables, like thread starter.
But I cannot see anything wrong with my speaker/signal outputs or cables.
The solderings look fine, and all cables are checked and double-checked.
Any tips?
An externally hosted image should be here but it was not working when we last tested it.
An externally hosted image should be here but it was not working when we last tested it.
Last edited:
there is a mute function. in order for modules to work you need connect black wire J4 (most inner one next to fast on connectors) with earth on module itself.
Problem solved ! shortcut in the speaker output.
I take the cables off, amplifier off/on with cables.
Working.....
OK, so the output shortcircuit protection really works and saved your unit. Well done, Hypex!
there is a mute function. in order for modules to work you need connect black wire J4 (most inner one next to fast on connectors) with earth on module itself.
Thanks for the response.
J4 on my HG supply is + (red cable) to the module. I also have a ground from the supply to each module (J2/J5, black cable).
Everything is connected according to the hypex instructions:
Downloads
You have no input ground/-
the molex connector pin out should be
starting from black thin black wire mute off/on or amp on/off
signal -
signal ground
signal +
if you are running rca inputs you will need to connect signal - with signal ground and then connect to these rings that stick out in the middle with absolutely nothing connected to them.
the molex connector pin out should be
starting from black thin black wire mute off/on or amp on/off
signal -
signal ground
signal +
if you are running rca inputs you will need to connect signal - with signal ground and then connect to these rings that stick out in the middle with absolutely nothing connected to them.
Of course, how could I forget input ground 🙂
but then again I'm a noob and this was all new to me
Thanks a lot mate!
but then again I'm a noob and this was all new to me
Thanks a lot mate!
any one can help me hypex PSC 2.400 NOT working
Hypex pcs 2.400 is not working !
no out put coming from the amp out !
DEAR ALL.. any one can help me to fix this problem !
Hypex pcs 2.400 is not working !
no out put coming from the amp out !
DEAR ALL.. any one can help me to fix this problem !
Last edited:
- Status
- Not open for further replies.
- Home
- Amplifiers
- Class D
- Hypex problem, who can help