Hi Luck ,
Nice work . Congratulations .
I did have the oportunity to service and to listen many hybrid
amps , most of them built by the former Counterpoint Company,
and all of them did sound very , very nice .
I think that yours sounds very nice too , mainly due to the simplicity.
IMHO , simplicity is the first goal ,if you want to get a good sound
in any Hi-Fi or DIYaudio project .
Off Topic :
The “ Gotan Project “ is a good “sound” , too . Did you know that
Gotan is an anagram of Tango that is the Argentina native rhythm ??
Carlos
Nice work . Congratulations .
I did have the oportunity to service and to listen many hybrid
amps , most of them built by the former Counterpoint Company,
and all of them did sound very , very nice .
I think that yours sounds very nice too , mainly due to the simplicity.
IMHO , simplicity is the first goal ,if you want to get a good sound
in any Hi-Fi or DIYaudio project .
Off Topic :
The “ Gotan Project “ is a good “sound” , too . Did you know that
Gotan is an anagram of Tango that is the Argentina native rhythm ??
Carlos
Hi refference ,
Thanks for your reply.I had a workshop in China and make so many types of tube amplifiers just like 300B,845,el34,6c33 etc.
i like 300B SE very much,which also use another 300B works as power supply,haha.
Thanks for your reply.I had a workshop in China and make so many types of tube amplifiers just like 300B,845,el34,6c33 etc.
i like 300B SE very much,which also use another 300B works as power supply,haha.
Hi Luck ,
Nice work , congratulations again .
I do like this one more than the first one .
Carlos
Nice work , congratulations again .
I do like this one more than the first one .
Carlos
There are more information of tube hybrid amplifier for your reference.
http://www.head-fi.org/forums/f21/audio-gd-panther-power-amp-anyone-419935/
http://www.head-fi.org/forums/f21/audio-gd-panther-power-amp-anyone-419935/
Hi Luck, greetings from Japan!
I bought two PCB's in ShenZhen, China. The PCB's are as follows:
1: 6N3-T tube based line amplifier
2: Tripath TA2024 based Class-D Power Amplifier
These two PCB's are shown in my Blog below(sorry in Japanese).
http://ja1cty.at.webry.info/200903/article_7.html
I am planning to build HYBRID AMPLIFIER to utilize above two PCB's.
I hope the amplifier outputs cool sound at low frequency by Class-D
and brilliant sonic at middle frequency by 6N3-T.
I bought two PCB's in ShenZhen, China. The PCB's are as follows:
1: 6N3-T tube based line amplifier
2: Tripath TA2024 based Class-D Power Amplifier
These two PCB's are shown in my Blog below(sorry in Japanese).
http://ja1cty.at.webry.info/200903/article_7.html
I am planning to build HYBRID AMPLIFIER to utilize above two PCB's.
I hope the amplifier outputs cool sound at low frequency by Class-D
and brilliant sonic at middle frequency by 6N3-T.
Nice work guys.
This is my latest project.
This a hybrid class D amp. I used 2 x Hypex UCD180, bypassed the input opamp buffer with JJ E88CC gold ( balanced and matched) SRPP stage and used a Classic housing( not a small one) and Rcore transformer. 4 inputs and Alps potmeter.
And it sounds relaxed you can listen the hole day to it.
Ronny
This is my latest project.
An externally hosted image should be here but it was not working when we last tested it.
This a hybrid class D amp. I used 2 x Hypex UCD180, bypassed the input opamp buffer with JJ E88CC gold ( balanced and matched) SRPP stage and used a Classic housing( not a small one) and Rcore transformer. 4 inputs and Alps potmeter.
And it sounds relaxed you can listen the hole day to it.
Ronny
Hi,all
Hi,all,it seems the PCB above is a 6N3(5670) SRPPdesigned.
My design is a ECC88 srpp output stage.And i use LM3886 as the power output.
Hi,all,it seems the PCB above is a 6N3(5670) SRPPdesigned.
My design is a ECC88 srpp output stage.And i use LM3886 as the power output.
Yes luck it was a 6N3 design. I have changed it for E88CC, next time i order a 6N11( E88CC) board. Futher i changed the coppling capacitors for Spraque and Wima( not on the photo).
Ronny
Ronny
- Status
- Not open for further replies.