There is no cheap analog voltmeter in 100-200mV range.
I don't want to remove R32, and tying in an appropriate amp meter in the 1-1.5A range.
I don't know, it can be understandable my problem?
I don't want to remove R32, and tying in an appropriate amp meter in the 1-1.5A range.
I don't know, it can be understandable my problem?
it's simple as this
source resistor or resistor in series with rail ( lazy to look at schmtc)
just calc do you have enough voltage across said resistor to have enough current through voltmeter for mid position of needle , which is half of declared current
source resistor or resistor in series with rail ( lazy to look at schmtc)
just calc do you have enough voltage across said resistor to have enough current through voltmeter for mid position of needle , which is half of declared current
Attachments
Last edited:
Yes, I thought something similar.
But I must to know those cheap ammeters internal resistance to choose the proper one.
But I must to know those cheap ammeters internal resistance to choose the proper one.
There was an accident.
I was tried to raise quiescent current a little, while monitored changes with those VU meters. Then there was some work and phone calls I must have to answered, so it was remained alone without supervision. Know, it is my fault.
So as I come back, there was a huge DC offset at outputs, 7VDC and 5VDC on other half (channel).
I switched off immediatelly, and began to trace, what could happened?
And what was damaged.
It wasn't a really good feeling, I can say.
First I've measured resistance between drains of Sony VFETs.
It was about 2-2.5 Ohm, as usual in switched off.
So definitely not short circuit.
I think even in California it was possible to hear how the rock rolled out about my heart. Isn't it, Papa?
Further investigation showed, one of the channels lost its negative PS voltage.
It revealed later, it was because two 0.47 Ohm resistor between supply caps went south. They were almost open circuit in Mohm range.
Replaced them, a big breath and switched on with light bulb series with AC line.
Everything went well.
Sonido speaker, which was connected also survived, because it was connected between positive terminals of two channels.
It works flawlessly now.
I can't understand, why those two resistors must have to die?
I was tried to raise quiescent current a little, while monitored changes with those VU meters. Then there was some work and phone calls I must have to answered, so it was remained alone without supervision. Know, it is my fault.
So as I come back, there was a huge DC offset at outputs, 7VDC and 5VDC on other half (channel).
I switched off immediatelly, and began to trace, what could happened?
And what was damaged.
It wasn't a really good feeling, I can say.
First I've measured resistance between drains of Sony VFETs.
It was about 2-2.5 Ohm, as usual in switched off.
So definitely not short circuit.
I think even in California it was possible to hear how the rock rolled out about my heart. Isn't it, Papa?
Further investigation showed, one of the channels lost its negative PS voltage.
It revealed later, it was because two 0.47 Ohm resistor between supply caps went south. They were almost open circuit in Mohm range.
Replaced them, a big breath and switched on with light bulb series with AC line.
Everything went well.
Sonido speaker, which was connected also survived, because it was connected between positive terminals of two channels.
It works flawlessly now.
I can't understand, why those two resistors must have to die?
I have two Veteran's PSU panel/channel, with four 22000uF caps on each PSU board, so total of four PSU board/amp.
There are two 0.47Ohm resistors parallel, on each panel in middle of.
There are two 0.47Ohm resistors parallel, on each panel in middle of.
On two parallel 3 watt 0.47 Ohm resistor there is flows about 1A current.
There is a voltage drop about 220mV, so I really can't understand, what happened and why.
There is a voltage drop about 220mV, so I really can't understand, what happened and why.
On a somewhat similar note (initial current) which in this case is probably a whole lot more!
http://www.diyaudio.com/forums/pass-labs/124889-b1-buffer-preamp-145.html#post5170015
Tony.
http://www.diyaudio.com/forums/pass-labs/124889-b1-buffer-preamp-145.html#post5170015
Tony.
Yes, VU-meters showed an initial over voltage on R32.
These were not calibrated.
Also, DMMs too lazy to show initial peak correctly.
Perhaps I can measure it with one of my scope.
In this case Tek 2440 would be appropriate I think.
But I must pay attention to measuring arrangement, I can't connect ground lead to any legs of R32 of course. 😉
These were not calibrated.
Also, DMMs too lazy to show initial peak correctly.
Perhaps I can measure it with one of my scope.
In this case Tek 2440 would be appropriate I think.
But I must pay attention to measuring arrangement, I can't connect ground lead to any legs of R32 of course. 😉
can you phone him and ask are my drivers still at his shelf ..... C45 Lowthers (needing new spiders and soldering of VC ends) and bare baskets of Electrovoice 12trxb (as base for 12" extended/full rangers)
my emails are evidently finishing in black hole , or something ......
my emails are evidently finishing in black hole , or something ......
- Status
- Not open for further replies.