Hi Guys. I started to received the payments, but so far 1 guy paid in $CAN. Since $CAN is much lower and the U$, and that I paid mostly in U$, I end up short... For example 50$CAN is only 37.55U$, you see the problem...
Please make sure to send U$ funds to my Paypal, not $CAN. Thanks for your understanding...
SB
Please make sure to send U$ funds to my Paypal, not $CAN. Thanks for your understanding...
SB
Last edited:
arnd13 - 1 board
passive420 - 2 boards
Bvtrinh - 1 board
Morde - 2 boards (PAID)
Arthur - 2 boards
Hiker47 - 2 boards
hy2a3 - 1 board
ginum - 1 board (PAID)
Johnny Canuck - 1 board
Cork Lad - 2 Boards
Documentation already sent to your private email for those who paid.
I'll ship all the paid kits on Friday, before I leave
The rest will be shipped once I return, first week on July (assuming that you paid naturally)
passive420 - 2 boards
Bvtrinh - 1 board
Morde - 2 boards (PAID)
Arthur - 2 boards
Hiker47 - 2 boards
hy2a3 - 1 board
ginum - 1 board (PAID)
Johnny Canuck - 1 board
Cork Lad - 2 Boards
Documentation already sent to your private email for those who paid.
I'll ship all the paid kits on Friday, before I leave
The rest will be shipped once I return, first week on July (assuming that you paid naturally)
Last edited:
Some asked me about the heatsink bracket, my own version, yours can be what ever you want, but mine fit the pcb layout...
Material aluminum corner, thickness 1/4'', Dimensions: H2''xD1-5/8''(top section)xL6''
You can use a much smaller corner bracket, mine is recycled from scrap metal I have in stock...
Took me 2 hours from start to finish, first cutting to size, I used my bench saw with none ferous blade, but VERY DANGEROUS, DON'T TRY IT IF YOU DON'T KNOW WHAT YOU'RE DOING... Naturally with a metal hand saw it is much safer. Then some holes marking, drilling, threading, and finally some brushing finishing touch...
Material aluminum corner, thickness 1/4'', Dimensions: H2''xD1-5/8''(top section)xL6''
You can use a much smaller corner bracket, mine is recycled from scrap metal I have in stock...
Took me 2 hours from start to finish, first cutting to size, I used my bench saw with none ferous blade, but VERY DANGEROUS, DON'T TRY IT IF YOU DON'T KNOW WHAT YOU'RE DOING... Naturally with a metal hand saw it is much safer. Then some holes marking, drilling, threading, and finally some brushing finishing touch...
Attachments
Last edited:
Assembled my prototype this afternoon, and even if mine was modified to +/-24V, not dual mono, it is working just fine. Primaries selection was only tested at 120V, but will work fine at 240V.
Note: This is a VERY HIGH current DC power supply. It can supply a lot of juice and there is no fuse protection on the rails. So don't short them... The simple regs are current limited and the +-15V supplies outputs will be protected.
Also since I modified the board I was able to judge the pcb quality, and yes it is. Great copper traces difficult to cut, good solder mask hard to scratch, good pads. It is a very good quality board, so no need to worry.
Also all the parts I used fit just fine to pcb. Assembled correctly this board will work the first time
Note: This is a VERY HIGH current DC power supply. It can supply a lot of juice and there is no fuse protection on the rails. So don't short them... The simple regs are current limited and the +-15V supplies outputs will be protected.
Also since I modified the board I was able to judge the pcb quality, and yes it is. Great copper traces difficult to cut, good solder mask hard to scratch, good pads. It is a very good quality board, so no need to worry.
Also all the parts I used fit just fine to pcb. Assembled correctly this board will work the first time
Attachments
All members paid, and I shipped all kits just a few minutes ago. Some were sent Air small parcel, some a simple envellop, depending on weight and/or destination. Please allow 5-10 working days for delivery, maybe a little more for some European countries (by experience).
Please let me know once you get the package, so I can conclude the transaction.
Thanks
SB
Please let me know once you get the package, so I can conclude the transaction.
Thanks
SB
- Status
- This old topic is closed. If you want to reopen this topic, contact a moderator using the "Report Post" button.
- Home
- Group Buys
- GB for Pioneer Super Linear Motherboard