FS: NOS G.E. 7025 tube long-plate
This is a NOS G.E. 7025 tube. I bought this in a large lot of tubes eons ago near Syracuse, NY. The box was moldy and falling apart so it lives in a nice white box now.
This tube test like a NOS tube should on my B&K707.
Paypal as a gift or bank transfer.
35 euro plus shipping.
This is a NOS G.E. 7025 tube. I bought this in a large lot of tubes eons ago near Syracuse, NY. The box was moldy and falling apart so it lives in a nice white box now.
This tube test like a NOS tube should on my B&K707.
Paypal as a gift or bank transfer.
35 euro plus shipping.
Attachments
FS: NOS Tung-Sol 12AX7A tube
A NOS Tung-Sol 12AX7A tube. The original box was moldy and falling apart so it lives in a nice white box now.
Tests as a NOS tube should on my B&K707.
25 euro plus shipping.
Paypal as a gift or bank transfer.
Thanks!
A NOS Tung-Sol 12AX7A tube. The original box was moldy and falling apart so it lives in a nice white box now.
Tests as a NOS tube should on my B&K707.
25 euro plus shipping.
Paypal as a gift or bank transfer.
Thanks!
Attachments
FS: 10 (ten) ECL86 / 6GW8 tubes Mullard
Ten ECL86 / 6GW8 tubes. There are mostly Phillips/Mullard and some Japanese Phillips.
Make me a reasonable offer and they are yours.
They have all been tested on my B&K707.
paypal as a gift or bank transfer.
Ten ECL86 / 6GW8 tubes. There are mostly Phillips/Mullard and some Japanese Phillips.
Make me a reasonable offer and they are yours.
They have all been tested on my B&K707.
paypal as a gift or bank transfer.
Attachments
FS: Tubelab SE PCB Assembled/stuffed
Tubelab SE board assembled but never used.
The semiconductors are all included as well as a pair of .1uf 600v Orange Drop coupling caps.
The mosfets are sk3564's.
These have not been installed yet.
You will need to add the jumpers to set the filament voltage for either 300B or 45 tubes.
The heatsinks, R4 (spot for choke) and R3 are NOT INCLUDED!!!! (R3 is the 2.2R adjustment resistor for the dc filaments on the 5842's).
This board is not really for beginners; you need to have some knowledge of vacuum tube electronics and experience working with these voltages.
Have a look at the pics.
65 euros free shipping in the E.U. (continental)
Tubelab SE board assembled but never used.
The semiconductors are all included as well as a pair of .1uf 600v Orange Drop coupling caps.
The mosfets are sk3564's.
These have not been installed yet.
You will need to add the jumpers to set the filament voltage for either 300B or 45 tubes.
The heatsinks, R4 (spot for choke) and R3 are NOT INCLUDED!!!! (R3 is the 2.2R adjustment resistor for the dc filaments on the 5842's).
This board is not really for beginners; you need to have some knowledge of vacuum tube electronics and experience working with these voltages.
Have a look at the pics.
65 euros free shipping in the E.U. (continental)
Attachments
FS: 10 (ten) Tungsol 6CG7 tubes
Ten Tung-Sol 6CG7 tubes. They all test in the green on my B&K707 tester. These all have an internal shield.
The printing is mostly all worn off of the tubes. Have a look at the pics.
30 euro, paypal as a gift or bank transfer.
I am near Vienna, Austria.
Ten Tung-Sol 6CG7 tubes. They all test in the green on my B&K707 tester. These all have an internal shield.
The printing is mostly all worn off of the tubes. Have a look at the pics.
30 euro, paypal as a gift or bank transfer.
I am near Vienna, Austria.
Attachments
Last edited:
- Status
- This old topic is closed. If you want to reopen this topic, contact a moderator using the "Report Post" button.