class D audio power amplifier using tas 5261 IC.

[surya krishna]

We are doing project work on class D audio power amplifier. For that we are using TAS5261 IC and pga2310 using as a volume control, tpa 2310 as a pulse width modulator.

Sir, we are suffering from simmulator for this and also HOW TO INTERFACE?. And also circuit diagram.


THANKYOU.

 

[surya krishna]

simulator require.

We are under taken the project "class D type audio power amplifier "using TEXAS IC TAS5261.And we are interfacing the PGA2311(VOLUME CONTROLLER) and TPA2000D1 with TAS5261. We require "simulator software " for this project.so i request you to please help me.

 

[surya krishna]

simulator

I require simulator software for class d type audio power amplifier if available please help me ........manohar

 

[koolkid731]

Does one get a degree for doing this kind of homework?

 

[BWRX]

Re: simulator require.

And we are interfacing the PGA2311(VOLUME CONTROLLER) and TPA2000D1 with TAS5261. We require "simulator software " for this project.so i request you to please help me.

That part about the TPA2000D1 and TAS5261 sounds so familiar... I seem to remember seeing something like that before... A search for "TAS5261" in the class d forum should return something useful.

As far as the simulator software goes, I really doubt you'll find someone willing to help you out for nothing.

 

[surya krishna]

pcb design

require pcb designing for tas5261 with tpa2000d1(pulse width modulation) and pga 2311(volume controller).how to get it?
thank you
manohar

 

[Eva]

Re: pcb design

how to get it?

By learning to route PCB yourself? 😉

 

[jacco vermeulen]

Dormido bien yo veo, "es la Mejor" Lista.

 

[ChocoHolic]

Re: Re: pcb design

By learning to route PCB yourself? 😉

Bad girl ! 😀

Surya,
you could go for TinyCAD in order to draw the schematic and export into a netlist.
For layouting you could use FreePCB.

 

[fumac]

Re: Re: Re: pcb design

Bad girl ! 😀

Surya,
you could go for TinyCAD in order to draw the schematic and export into a netlist.
For layouting you could use FreePCB.

ChocoHolic
EVA is a girl???

cracy and great 🙂

FUMAC

 

[ChocoHolic]

... there was already a discussion in other threads about Eva and the question if she is real or fake.
For me she is a girl, even if she knows SMPS better than I do.

But let's stick to topic....

 

[Malquis]

Hi, my reply isn't to turn you down but I think you are trying t obuild something quite above your level, first because if you don't know what soft to use you obiusly haven't been on designing boards quite much I'd recommend you protel99 or livewire kit though, and secon you haven't been able to find any application information.
Well to find som you should look in texas aplications pdf there is always some design of their products.I'm shure you'll find some there.
I'd sugest you to start with something easier for example, the one I've studied, the TAS5100, there is also a design including board.
Any way hope you make it class D texas amps are wonderful, they don't waste enery like valve amps or heating like he..ll as class A and the bes of all the signal is THE ORIGINAL one that came frome the source bye bye noise. nice huu!
Look for this app note on texas cause I couldn't upload it for you
"sleu010a5100" there is a whole board designed, not too complicated 2 channels 30W, analog or digital input.
Bye

 

[surya krishna]

tas5261

Excuse me i am the student of M.Sc(tech)Electronics&instrumentation.
my project left the simulator for pcb designing of
TAS 5261.RESPOND TO MY POST.

THANK YOU
SURYA KRISHNA MANOHAR















😡

 

[surya krishna]

tas 5261

require simulator for tas5261
thank u
manohar

 

[BWRX]

Re: tas 5261

require simulator for tas5261

These forums are not to be used in the manner you are attempting to use them. Please do your own work and stop spamming the forum with requests that someone do it for you.