support
Have a second look on the ARTA homepage
http://www.fesb.hr/~mateljan/arta/support.htm
There is a new category
Have a second look on the ARTA homepage
http://www.fesb.hr/~mateljan/arta/support.htm
There is a new category
Very nice. I've used Arta a few times for quick frequency response measurements, it is far easier than Speaker Workshop. If I had one feature request it would be for continuous moving average frequency display.
Dan
Dan
ARTA Release 1.01
Hi,
ARTA Release 1.01 with al lot of new features is available now.
Have a look on Ivo's Homepage
http://www.fesb.hr/~mateljan/arta/download.htm
Regards
Heinrich
Hi,
ARTA Release 1.01 with al lot of new features is available now.
Have a look on Ivo's Homepage
http://www.fesb.hr/~mateljan/arta/download.htm
Regards
Heinrich
ARTA Release 1.0.3
Hi guys,
ARTA Release 1.0.3 is available now -->
http://www.fesb.hr/~mateljan/arta/download.htm
Regards
Heinrich
Hi guys,
ARTA Release 1.0.3 is available now -->
http://www.fesb.hr/~mateljan/arta/download.htm
Regards
Heinrich
Having trouble. I've tried this software on two computers with different soundcards, same result. Using "Steps" each time the frequency changes there is a loud pop before and after the tone being played. Any ideas?
PLOP
don't call it trouble 😉
The plop ist just a little bit annoying but it makes no trouble to your DUT (if you be careful with the input signal)!
Regards
Heinrich
don't call it trouble 😉
The plop ist just a little bit annoying but it makes no trouble to your DUT (if you be careful with the input signal)!
Regards
Heinrich
Re: PLOP
What is "DUT"?
Secondly, how is it possible that this very loud pop would not effect the measurement? Do I understand correctly that this pop is "normal"?
ente said:
What is "DUT"?
Secondly, how is it possible that this very loud pop would not effect the measurement? Do I understand correctly that this pop is "normal"?
I have yet to hear a noise from the setup I have, other than what is suppose to be there. Hence, my suggestion about checking your gain.
Mark
Mark
New release
Hi guys,
ARTA release 1.1.0 is available on Ivo's homepage:
http://www.fesb.hr/~mateljan/arta/news.htm
Have fun with it 😀
Heinrich
Hi guys,
ARTA release 1.1.0 is available on Ivo's homepage:
http://www.fesb.hr/~mateljan/arta/news.htm
Have fun with it 😀
Heinrich
I've been using Arta with an m-audio 2496 internal sound card and via spdif with an external dac. Works very well indeed. Will download the latest version shortly.
I like this enough that I will purchase it as a replacement for Audiotester which on both of my systems is quite buggy.
I like this enough that I will purchase it as a replacement for Audiotester which on both of my systems is quite buggy.
I would like to use Arta with my Creative Audigy. Does someone know its imput impedance? Are the value R1=8200 ohms and R2=910 ohms ok for my soundcard?
ARTA 1.2
Delayed Xmas announcement.
In one or two weeks you can download ARTA 1.2. Here are some of the news:
ARTA
- CSD also as spectrogram
- directivity plot, new
- excess phase and excess group delay, update
- new IMD intermodulation distortion report (SMPTE, CCIF, DIN, IEC 60268-5), new
- new THD report
- max. impulse response sequence length extended to 256k (for reverberation time measurements in large rooms)
- reverberation time can be estimated in octave bands 62.5, 125,.. , 8000Hz
- output volume for multi sine extended to -30dB
- control of graph setup, update
- gate time can be shown as equivalent sound wave propagation distance in cm
- 192kHz sampling rate enabled
corrections of small bugs
- ascii file export of the step response
- correct swept-sine timing
LIMP
- optimized procedure for the estimation of TSP
Happy New Year
Heinrich 😉
Delayed Xmas announcement.
In one or two weeks you can download ARTA 1.2. Here are some of the news:
ARTA
- CSD also as spectrogram
- directivity plot, new
- excess phase and excess group delay, update
- new IMD intermodulation distortion report (SMPTE, CCIF, DIN, IEC 60268-5), new
- new THD report
- max. impulse response sequence length extended to 256k (for reverberation time measurements in large rooms)
- reverberation time can be estimated in octave bands 62.5, 125,.. , 8000Hz
- output volume for multi sine extended to -30dB
- control of graph setup, update
- gate time can be shown as equivalent sound wave propagation distance in cm
- 192kHz sampling rate enabled
corrections of small bugs
- ascii file export of the step response
- correct swept-sine timing
LIMP
- optimized procedure for the estimation of TSP
Happy New Year
Heinrich 😉
I've been running the trial version of this for a few months now. I've got to say that its an excellent package that does all the important measurements with accuracy. Just in case you aren't familiar with what it can do here's the main attractions: Room, TS measurements, distortion, FR, phase, impedance, impulse and the list goes on and on.
The real bonus is that its so easy to use, with most measurements taking only seconds. This means more tweaking and less concentrating and messing around with software. Its also nice to see that its updated regularly with all the latest features.
I just bought it using the Share-it option on the ARTA webpage. I was amazed that it only cost £57, I was expecting it to be significantly more than that.
Whole heartedly recommended, probably the best measurement package out there - tons of power yet easy to use.
The real bonus is that its so easy to use, with most measurements taking only seconds. This means more tweaking and less concentrating and messing around with software. Its also nice to see that its updated regularly with all the latest features.
I just bought it using the Share-it option on the ARTA webpage. I was amazed that it only cost £57, I was expecting it to be significantly more than that.
Whole heartedly recommended, probably the best measurement package out there - tons of power yet easy to use.