I have one of these and the reverb isn't working. I've ruled out the tank and connectors. I though it might be worth a shot to see if anybody has one that they could share with me. I've looked and haven't been able to find one. Thanks!
There is a Loudbox schematic here: https://music-electronics-forum.com/attachment.php?attachmentid=44746&d=1504378726
This is the thread if the above link doesn't work: Loudbox mini
You may need to join the MEF to see the file.
Stph
This is the thread if the above link doesn't work: Loudbox mini
You may need to join the MEF to see the file.
Stph
Dear Kevinaston1
Do you happen to have the schematics for the Loudbox Artist model?
By chance any mechanical drawings?
I am trying to fix one - can't seem to find a way to open the bottom "main" enclosure which contains the speakers, power transformer etc...
THX a lot
Do you happen to have the schematics for the Loudbox Artist model?
By chance any mechanical drawings?
I am trying to fix one - can't seem to find a way to open the bottom "main" enclosure which contains the speakers, power transformer etc...
THX a lot
Fishman Loudbox Artist
All the electronics for the artist are in the metal chassis at the top, remove three screws at each side at the top, and lift the chassis out - ensure you disconnect the loudspeaker lead before lifting the chassis right out.
If you need access to the "base of the unit", gently prise off the loudspeaker grille, and remove the bass driver - but it is just air in there.
Schematic attached.
Kevin
All the electronics for the artist are in the metal chassis at the top, remove three screws at each side at the top, and lift the chassis out - ensure you disconnect the loudspeaker lead before lifting the chassis right out.
If you need access to the "base of the unit", gently prise off the loudspeaker grille, and remove the bass driver - but it is just air in there.
Schematic attached.
Kevin
Thanks a lot Kevin
Sorry for the delayed response, I wasn't logged in on my phone and your post somehow didn't sow up there :/
Was able to check the bottom part now indeed.
The schematics you have attached are not for the same model though.
The Artists model has a bank of 4 voltage regulators at -14, 14, 12 and 24V
See Fishman Loudbox Artist Repair question : GuitarAmps and Fishman2 - Google Photos
Sorry for the delayed response, I wasn't logged in on my phone and your post somehow didn't sow up there :/
Was able to check the bottom part now indeed.
The schematics you have attached are not for the same model though.
The Artists model has a bank of 4 voltage regulators at -14, 14, 12 and 24V
See Fishman Loudbox Artist Repair question : GuitarAmps and Fishman2 - Google Photos
Dear all,
I spent some time drawing this schematics for the main board. Lots of fun (first time I'm doing that!) , obviously lots of errors/incorrectness (I didn't do a proper set of hierarchical sheets ; not sure if my global labels are the proper way to do that ; R values are a bit all over the place🙂
R1 looks weird. (see my other post). Would a burned resistor measure a higher value than its nominal? If not, why would it be one order of magnitude higher resistance than its three siblings R32 R33 and R34 ?
THX
Dropbox - PDFs - Simplify your life
I spent some time drawing this schematics for the main board. Lots of fun (first time I'm doing that!) , obviously lots of errors/incorrectness (I didn't do a proper set of hierarchical sheets ; not sure if my global labels are the proper way to do that ; R values are a bit all over the place🙂
R1 looks weird. (see my other post). Would a burned resistor measure a higher value than its nominal? If not, why would it be one order of magnitude higher resistance than its three siblings R32 R33 and R34 ?
THX
Dropbox - PDFs - Simplify your life
Old post, I know...
but checking if anyone has come up with a schematic for the Loudbox Artist?
(Not the "Mini", or the "100", or other models)
The Artist has two input channels with combo jacks (1/4"-xlr), and is supposed to accomodate both instruments and microphones.
the one I'm working on works fine with the 1/4" inputs, nothing thru the XLR.
I found a User Manual that contains this block diagram, but I can't seem to find a schematic...
but checking if anyone has come up with a schematic for the Loudbox Artist?
(Not the "Mini", or the "100", or other models)
The Artist has two input channels with combo jacks (1/4"-xlr), and is supposed to accomodate both instruments and microphones.
the one I'm working on works fine with the 1/4" inputs, nothing thru the XLR.
I found a User Manual that contains this block diagram, but I can't seem to find a schematic...
Just to start with something, your block diagram shows jack input "always" connected to the full channel, while XLR goes through a dedicated Mic preamp (which must be Balanced input) which then connects to jack leaf switch, if it´s weak/worn/broken/dirty jack will still work, but you´ll ose Mic input.
In principle check that connector, spray a little Deoxit inside and work a plug in/out, check for broken/cracked solder/tracks, etc.
I expect a "mechanical" problem more than an "electronic" one.
In principle check that connector, spray a little Deoxit inside and work a plug in/out, check for broken/cracked solder/tracks, etc.
I expect a "mechanical" problem more than an "electronic" one.
yes that was my first thought, since it shows a switching jack, I have not opened it up yet, but I am anal about having schematics before I dive in...