ALPS RK168 50KAX2 100KAX2

[tommy54]

50KAX2 100KAX2 sold out


paypal(email) : oursmbt@163.com tian li

SKYPE: tplyyltli@hotmail.com




ALPS 100KAX4 6$ 64g used & checked well

ALPS 100KBX6 8$ 50kbx6 11$ new 70g

ALPS 27 100KBX2 5$

box 35g

50KAx2 100KAx2 50KAx4 50KBX6 PIN1-8：NC IN IN OUT GND GND OUT NC
100KAx4 100KBx6 PIN1-8：LOUDNEES IN IN LOUDNEES OUT GND OUT NC

 

[tommy54]

An externally hosted image should be here but it was not working when we last tested it.

An externally hosted image should be here but it was not working when we last tested it.

An externally hosted image should be here but it was not working when we last tested it.

button(47mm)&pcb 1$
ALPS pot 4$

 

[brik]

You have p.m.

 

[korben69]

PM + Paypal for 2 50KAX2

 

[tommy54]

PM + Paypal for 2 50KAX2

hi,I have posted 2 pieces.

 

[tommy54]

You have p.m.

I have posted 4 pots

 

[SY]

Since this is clearly a commercial venture, I am moving the thread to the Vendors' area.

 

[bogdan_borko]

You have p.m.

 

[bogdan_borko]

You have p.m. and email.

 

[tommy54]

ALPS RK168 50KAX6 8$

 

[Ed LaFontaine]

Please delete if this is OT.

I need a similar device in 20-25K. Can a parallel resistor be used on the 50K unit to lower the effective impedance to 20 or 25K?

Is this a "bad" idea?

 

[korben69]

hi,I have posted 2 pieces.

Hi Tommy
I've been delivered yesterday, fine packing !
Would you please post a wiring for RK168 and motorized pins ?
8 pins at the bottom and 2 pins at the rear for the "motor".
It could be helpfull
Cheers

 

[tommy54]

50KAX4 100KAX4
http://www.diyaudio.com/forums/swap-meet/192104-alps-rk168-50kax4-100kax4.html


pins description:

1.NC 2.LOUT 3.GND 4.GND(3,4 CONNECTED INSIDER)
5.ROUT 6.RIN 7.LIN 8.NC

 

[tommy54]

Please delete if this is OT.

I need a similar device in 20-25K. Can a parallel resistor be used on the 50K unit to lower the effective impedance to 20 or 25K?

Is this a "bad" idea?

It is feasible.

 

[korben69]

50KAX4 100KAX4
http://www.diyaudio.com/forums/swap-meet/192104-alps-rk168-50kax4-100kax4.html

pins description:

1.NC 2.LOUT 3.GND 4.GND(3,4 CONNECTED INSIDER)
5.ROUT 6.RIN 7.LIN 8.NC

Thank you for this pic and Pins connexions.
Could you post some informations about the PCB and Motor wiring/driving ?
Cheers

 

[tommy54]

Thank you for this pic and Pins connexions.
Could you post some informations about the PCB and Motor wiring/driving ?
Cheers

5v motor

 

[hybridspl]

I know this thread is old, but if these are still available, I would like two 50KAX2's.

 

[tommy54]

ok

 

[Dagwood]

Hi Tommy

Do you have any of the ALPS RK168 50KAX6 left?

Cheers

 

[Dagwood]

Oops, need the 100k not the 50k

Cheers